DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> Engine Control System (2GR-FKS) - Diagnostic Codes (2 Of 6) >> SFI System >> DTC P014C-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 1; DTC P014D-00: O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 1; DTC P014E-00: O2 Sensor Slow Response - Rich to Lean Bank 2 Sensor 1; DTC P014F-00: O2 Sensor Slow Response - Lean to Rich Bank 2 Sensor 1; DTC P015A-00: O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1; DTC P015B-00: O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1; DTC P015C-00: O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 1; DTC P015D-00: O2 Sensor Delayed Response - Lean to Rich Bank 2 Sensor 1 [12/2019 - 10/2022] >> Confirmation Driving Pattern

Confirmation Driving Pattern

HINT: 

GTY445687Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON.
  7. Turn the GTS on.
  8. Enter the following menus: Powertrain / Engine / Monitor / Current Monitor.
  9. Check that O2 Sensor / Current is Incomplete.

    HINT: 

    The test values for the test items RL RESPONSE RATE B1S1, LR RESPONSE RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RESPONSE RATE B2S1, LR RESPONSE RATE B2S1, RL DELAY B2S1 and LR DELAY B2S1 do not exist in the Detail of O2 Sensor monitor at this time (the initial value of "0.000" is indicated in each test item).

  10. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) [A].
  11. Drive the vehicle at a constant speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].
    WARNING:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Check that O2 Sensor / Current becomes Complete.

    HINT: 

    Check the test values on the GTS by entering the following menus: Powertrain / Engine / Monitor / Current Monitor / O2 Sensor / Details / RL RESPONSE RATE B1S1, LR RESPONSE RATE B1S1, RL DELAY B1S1, LR DELAY B1S1, RL RESPONSE RATE B2S1, LR RESPONSE RATE B2S1, RL DELAY B2S1 and LR DELAY B2S1.

  13. If the monitor item O2 Sensor / Current does not become Complete (if the test values indicated on the GTS do not change), perform Readiness Monitor Drive Pattern for the air fuel ratio sensor and heated oxygen sensor.

    Refer to READINESS MONITOR DRIVE PATTERN [12/2019 - 10/2022]

  14. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
  15. Read the pending DTCs.

    HINT: 

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  17. Input the DTC: P014C-00, P014D-00, P014E-00, P014F-00, P015A-00, P015B-00, P015C-00 or P015D-00.
  18. Check the DTC judgment result.
    GTS Display Description
    NORMAL
    • DTC judgment completed
    • System normal
    ABNORMAL
    • DTC judgment completed
    • System abnormal
    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT: 

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • [A] to [C]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
Diesel-Data.com