DTC B1579-13: Voice Recognition Microphone1 Circuit Open [10/2022 - ]: Procedure
- CHECK MODEL
Result
Result Proceed to w/ DCM (Telematics Transceiver) A w/o DCM (Telematics transceiver) B Result:
B
See step 4
Result:
A
See step 2
- CHECK HARNESS AND CONNECTOR (TELEPHONE MICROPHONE ASSEMBLY LH - RADIO AND DISPLAY RECEIVER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER))
- Disconnect the R25 telephone microphone assembly LH connector.
- Disconnect the H108 radio and display receiver assembly connector.
- Disconnect the H11 DCM (telematics transceiver) connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition R25-5 (SNS1) - H108-25 (SNS) Always Below 1 Ω R25-4 (MO1-) - H11-7 (MCI-) Always Below 1 Ω R25-5 (SNS1) or H108-25 (SNS) - Body ground Always 10 kΩ or higher R25-4 (MO1-) or H11-7 (MCI-) - Body ground Always 10 kΩ or higher Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 3
- INSPECT DCM (TELEMATICS TRANSCEIVER) (MCI-)
- With the DCM (telematics transceiver) connectors connected, disconnect the R25 telephone microphone assembly LH connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition R25-4 (MO1-) - Body ground Always Below 1 Ω Result
Proceed to OK NG
Result:
OK
See step 6
Result:
NG
REPLACE DCM (TELEMATICS TRANSCEIVER)
Refer to REMOVAL [10/2022 - 11/2023] , or refer to REMOVAL [11/2023 - ]
- CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY LH)
- Disconnect the H108 radio and display receiver assembly connector.
- Disconnect the R25 telephone microphone assembly LH connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition R25-5 (SNS1) - H108-25 (SNS) Always Below 1 Ω R25-4 (MO1-) - H108-22 (MIN-) Always Below 1 Ω R25-5 (SNS1) or H108-25 (SNS) - Body ground Always 10 kΩ or higher R25-4 (MO1-) or H108-22 (MIN-) - Body ground Always 10 kΩ or higher Result
Proceed to OK NG
Result:
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
OK
See step 5
- INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (MIN-)
- With the radio and display receiver assembly connectors connected, disconnect the R25 telephone microphone assembly LH connector.
- Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition R25-4 (MO1-) - Body ground Always Below 1 Ω Result
Proceed to OK NG
Result:
NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
Refer to REMOVAL [10/2022 - 11/2023] , or refer to REMOVAL [11/2023 - ]
Result:
OK
See step 6
- INSPECT TELEPHONE MICROPHONE ASSEMBLY LH (SNS1, MO1-)
- Remove the telephone microphone assembly LH.
*a Component without harness connected
(Telephone microphone assembly LH) - Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection Condition Specified Condition 5 (SNS1) - 4 (MO1-) Always Below 1 Ω Result
Proceed to OK NG
Result:
OK
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
Refer to REMOVAL [10/2022 - 11/2023] , or refer to REMOVAL [11/2023 - ]
Result:
NG
REPLACE TELEPHONE MICROPHONE ASSEMBLY LH
Refer to REMOVAL [10/2022 - ]
- Remove the telephone microphone assembly LH.
