DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 67 (Hybrid Control System (AWD) - Diagnostic Codes (1 Of 6)) >> HYBRID CONTROL SYSTEM (for AWD) >> Vehicle Control History [12/2019 - 11/2023] >> Vehicle Control History [12/2019 - 11/2023]

Vehicle Control History [12/2019 - 11/2023]

WARNING: This page is about a different variant/trim than selected.
  1. CHECK VEHICLE CONTROL HISTORY (HYBRID CONTROL SYSTEM) 
    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History (RoB).

      Powertrain > Hybrid Control > Utility 

      Tester Display
      Vehicle Control History (RoB)

      HINT: 

      There are unimplemented function codes depending on vehicle specification.

      FFD Group Code Tester Display Measurement Item Diagnostic Note
      - X0450 Hybrid Battery Pack Sensor Module Mismatch Displays if the wrong type of battery voltage sensor is installed. Refer to PROBLEM SYMPTOMS TABLE [12/2019 - 10/2022] , or refer to PROBLEM SYMPTOMS TABLE [10/2022 - 11/2023]
      - X0460 Hybrid Battery Cooling Performance Decrement History of poor HV battery cooling performance Refer to PROBLEM SYMPTOMS TABLE [12/2019 - 10/2022] , or refer to PROBLEM SYMPTOMS TABLE [10/2022 - 11/2023]
      - X0500 Shift P Operation during Running History of shift lever being moved to P while driving -
      - X0509 Shift R/D Operation during Ready OFF History of shift state being changed to neutral (N) due to shift lever being held in R or D with ignition switch ON -
      - X050B Shift N Change by Busy Shift History of shift state being changed to neutral (N) due to shift lever being repeatedly moved to R, D and/or N within a short period of time -
      - X0520 HV System Start Up Failure by Very Low Temperature History of Hybrid Control System failing to start due to extremely cold environment -
      - X0521 HV System Start Up Failure by Immobiliser Unmatch History of Hybrid Control System failing to start due to Immobiliser System key verification failure -
      - X0522 Ready ON Failure by Shift Operation History of the ignition switch not being turned ON (READY) due to a shift operation -
      - X0523 Auxiliary Battery Voltage Low (HV) History of drop in hybrid vehicle control ECU power source voltage Stored when the auxiliary battery voltage to the hybrid vehicle control ECU drops below 9.5 V.
      - X0524 Auxiliary Battery Voltage Low (Inverter) History of drop in motor generator control ECU (MG ECU) power source voltage Stored when the auxiliary battery voltage to the motor generator control ECU (MG ECU) drops to 8.0 V or less.
      - X0526 HV System Stop Operation during Running History of Hybrid Control System being turned off by pressing ignition switch while vehicle being driven Stored when the ignition switch is turned off when the vehicle speed is 3 km/h (2 mph) or more.
      - X0527 Generator Temperature High History of extremely high generator (MG1) temperature and hybrid system overheated warning message being displayed Stored when the generator (MG1) temperature exceeds a certain value.
      - X0528 Generator Inverter Temperature High History of extremely high generator (MG1) inverter temperature and hybrid system overheated warning message being displayed Stored when the generator (MG1) inverter temperature exceeds a certain value.
      - X0529 Motor Temperature High History of extremely high motor (MG2) temperature and hybrid system overheated warning message being displayed -
      - X052A Motor Inverter Temperature High History of extremely high motor (MG2) inverter temperature and hybrid system overheated warning message being displayed Stored when the motor (MG2) inverter temperature exceeds a certain value.
      - X052B Rear Motor Temperature High History of extremely high rear motor (MGR) temperature and hybrid system overheated warning message being displayed -
      - X052C Rear Motor Inverter Temperature High History of extremely high rear motor (MGR) inverter temperature and hybrid system overheated warning message being displayed Stored when the rear motor (MGR) inverter temperature exceeds a certain value.
      - X052D Boosting Converter Temperature High History of extremely high boost converter temperature and hybrid system overheated warning message being displayed -
      - X0530 Staying Prevention Control History of operation of retention prevention function Stored when the engine speed remains in the resonance range.
      - X0531 Hybrid Battery Protection in Neutral Shift Position History of hybrid battery discharge warning message being displayed when vehicle left with shift lever in N -
      - X0532 HV Coolant Temperature High History of extremely high coolant (for inverter) temperature Stored when the coolant (for inverter) temperature is 65°C (149°F) or more.
      - X0536 Hybrid Battery Voltage Low History of Hybrid Control System starting failure due to low HV battery voltage -
      - X0537 HV System Start Up Failure by Hybrid Battery Unmatch History of Hybrid Control System starting failure due to an inappropriate HV battery -
      - X0539 Shift R Operation during Forward Movement or Shift D/B Operation during Backward Movement History of shift lever being moved to R while vehicle moving forward or shift lever being moved to D or S while vehicle moving backward -
      - X053A Shift Position Uncertain Shift position cannot be determined -
      02 X053B Engine Malfunction (Poor Engine Power) History of vehicle state during engine malfunction (poor engine power)
      (This information can be helpful for performing troubleshooting.)
      Stored when the ECM stores an SFI System DTC.
      Make sure to clear Vehicle Control History after performing troubleshooting related to this item.
      As all Vehicle Control History should be cleared after performing troubleshooting related this item, make sure to check any other output Vehicle Control History items and perform any troubleshooting for them before clearing Vehicle Control History.
      02 X053C Engine Malfunction (Engine does not Start) History of vehicle state during engine malfunction (engine does not start)
      (This information can be helpful for performing troubleshooting.)
      Stored when the ECM stores an SFI System DTC.
      Make sure to clear Vehicle Control History after performing troubleshooting related to this item.
      As all Vehicle Control History should be cleared after performing troubleshooting related this item, make sure to check any other output Vehicle Control History items and perform any troubleshooting for them before clearing Vehicle Control History.
      02 X053D Engine Malfunction (Crankshaft Position Sensor Signal) History of vehicle state during engine malfunction (abnormal crankshaft position sensor signal)
      (This information can be helpful for performing troubleshooting.)
      Stored when the ECM stores an SFI System DTC.
      Make sure to clear Vehicle Control History after performing troubleshooting related to this item.
      As all Vehicle Control History should be cleared after performing troubleshooting related to this item, make sure to check any other output Vehicle Control History items and perform any troubleshooting for them before clearing Vehicle Control History.
      02 X053E Engine Malfunction (GO Signal) History of vehicle state during engine malfunction (GO signal)
      (This information can be helpful for performing troubleshooting.)
      Stored when the ECM stores an SFI System DTC.
      Make sure to clear Vehicle Control History after performing troubleshooting related to this item.
      As all Vehicle Control History should be cleared after performing troubleshooting related to this item, make sure to check any other output Vehicle Control History items and perform any troubleshooting for them before clearing Vehicle Control History.
      02 X053F Engine Malfunction (Component Malfunction) History of vehicle state during engine malfunction (engine component malfunction)
      (This information can be helpful for performing troubleshooting.)
      Stored when the ECM stores an SFI System DTC.
      Make sure to clear Vehicle Control History after performing troubleshooting related to this item.
      As all Vehicle Control History should be cleared after performing troubleshooting related to this item, make sure to check any other output Vehicle Control History items and perform any troubleshooting for them before clearing Vehicle Control History.
      - X0541 Driver Exited Vehicle when Shift Position Wasn't P History of vehicle speed exceeding threshold after driver left vehicle with shift lever in any position other than P -
      - X054C Accelerator Depress when Shift P Position during Ready ON History of accelerator pedal depressed when shift lever in P and ignition switch ON (READY) -
      0c X055D Limit to Charge / Discharge Control Value by Hybrid Battery Temperature High History of HV battery charge/discharge being restricted
      If the temperature of the HV battery becomes approximately 44°C (111.2°F) or higher due to high ambient temperature, high cabin temperature, continuous driving under high load (such as mountain driving or frequent acceleration/deceleration), clogged hybrid battery intake duct, etc., the HV battery current will be restricted.
      In this case the value of WIN/WOUT will decrease and the engine will stop and start less frequently.
      1. If this Vehicle Control History item is stored, perform the following inspections.
        • Check the intake port of the HV battery cooling system for blockage, such as luggage, etc.
        • Check the Vehicle Control History Freeze Frame Data.
        • Check for clogs in the hybrid battery intake duct.
        • Inspect the HV battery cooling filter.

          Refer to INSPECTION [12/2019 - ]

      2. After performing the above inspections, check the temperature of the HV battery in the Data List.

        If the temperature of the HV battery is high (approximately 44°C (111.2°F) or higher), stop the vehicle, turn the air conditioning system on (Temperature: Lo, Blower speed: Max) and perform the Active Test "Control the Hybrid Battery Cooling Fan". Check that the temperature of the HV battery decreases.

      3. This Vehicle Control History item may be stored if the temperature of the HV battery became high due to certain conditions, such as if the ambient temperature was high, the cabin temperature was high or the vehicle was driven continuously under high load (such as mountain driving or frequent acceleration/deceleration).

        Explain to the customer that this is not a malfunction.

      0d X055E Limit to Charge / Discharge Control Value by Hybrid Battery Indicates whether Win/Wout is restricted due to causes other than HV battery temperature. -
      fe X0600 Auxiliary Battery Voltage Low at Start History of low auxiliary battery voltage at Hybrid Control System start -
      fd X0601 Auxiliary Battery Voltage Low at IG OFF History of low auxiliary battery voltage when ignition switch off -
      fc X0602 Auxiliary Battery Discharge at IG OFF History of auxiliary battery becoming discharged when ignition switch off -
      fb X0603 Auxiliary Battery Discharge at Running History of auxiliary battery becoming discharged while vehicle being driven -
  2. CLEAR VEHICLE CONTROL HISTORY (HYBRID CONTROL SYSTEM) 
    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History (Clear).
      NOTE:

      By performing this procedure, all stored Vehicle Control History items will be cleared.

  3. VEHICLE CONTROL HISTORY FREEZE FRAME DATA (HYBRID CONTROL SYSTEM) 
    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Powertrain / Hybrid Control / Utility / Vehicle Control History (RoB).

      Powertrain > Hybrid Control > Utility 

      Tester Display
      Vehicle Control History (RoB)
    5. Select a vehicle control history item to access the applicable Freeze Frame Data.
    6. Check the Freeze Frame Data recorded with the Vehicle Control History.
      GTS Display Description
      Target Engine Power Refer to DATA LIST / ACTIVE TEST
      Refer to DATA LIST / ACTIVE TEST [12/2019 - 11/2023]
      Execute Engine Power
      Target Engine Revolution
      Starter Switch Signal
      Engine Idling Request
      Engine Start Request (A/C)
      Engine Start Request (Engine Warm-up)
      Engine Start Request (Hybrid Battery Charging)
      Engine Mode
      Engine Stop Request
      Engine Stop F/C Status
      Lack of Fuel
      Accelerator Position
      Accelerator Pedal Status
      Master Cylinder Control Torque
      Shift Position
      Shift Position (Meter)
      Shift Position Sensor (PNB)
      Shift Position Sensor (PR)
      Shift Position Sensor (DB1)
      Shift Position Sensor (DB2)
      Shift Position Sensor (N)
      Shift Position Sensor (R)
      Shift Position Sensor (P)
      Sports Shift Position
      Sports Shift UP Signal
      Sports Shift DOWN Signal
      Transaxle Oil Temperature
      FR Wheel Speed
      FL Wheel Speed
      RR Wheel Speed
      RL Wheel Speed
      Forward and Rearward G
      Lateral G
      Yaw Rate Value
      Atmospheric Pressure
      Ambient Temperature
      Smoothed Value of BATT Voltage
      Total Distance Traveled
      Total Distance Traveled - Unit
      IGB Signal Status
      IG2 Signal Status
      Ready Signal
      Request READY ON Prevention (Hybrid Battery Pack Sensor Module Mismatch) Request ready on prevention (Hybrid battery pack sensor module mismatch)
      HV Activate Condition Refer to DATA LIST / ACTIVE TEST
      Refer to DATA LIST / ACTIVE TEST [12/2019 - 11/2023]
      MG Activate Condition
      DSS Control Status
      Generate Torque (Request from DSS)
      Primary Driving Force Adjustment Result
      WIN Control Limit Power
      WOUT Control Limit Power
      A/C Consumption Power
      Drive mode switch -
      Drive mode switch +
      EV Mode
      EV Mode Switch
      Crank Position
      Generator Revolution
      Target Generator Torque
      Generator Torque
      Motor Revolution
      Target Motor Torque
      Motor Torque
      Rear Motor Revolution
      Target Rear Motor Torque
      Rear Motor Torque
      Rear Motor Torque Ratio
      Request Motor Regenerative Brake Torque
      Motor Regenerate Brake Execution Torque
      Request Rear Motor Regenerative Brake Torque
      Rear Motor Regenerate Brake Execution Torque
      Generator Temperature
      Motor Temperature
      Rear Motor Temperature
      Motor Inverter Temperature
      Rear Motor Inverter Temperature
      Generator Inverter Operation Request
      Motor Inverter Operation Request
      Rear Motor Inverter Operation Request
      Boosting Converter Operation Request
      Generator Carrier Frequency
      Generator Control Mode
      Motor Carrier Frequency
      Motor Control Mode
      Rear Motor Carrier Frequency
      Rear Motor Control Mode
      Boosting Converter Carrier Frequency
      VL-Voltage before Boosting
      VH-Voltage after Boosting
      Boost Ratio
      DC/DC Converter Output Voltage Control Mode DC/DC converter output voltage control mode
      DC/DC Converter Target Voltage DC/DC converter target voltage
      DC/DC Converter Maximum Output Status DC/DC converter maximum output status
      Inverter Coolant Water Temperature Refer to DATA LIST / ACTIVE TEST
      Refer to DATA LIST / ACTIVE TEST [12/2019 - 11/2023]
      Inverter Water Pump Revolution
      Inverter Emergency Shutdown (Main CPU)
      Inverter Emergency Shutdown (Sub CPU)
      Hybrid Battery Voltage
      Hybrid Battery Current for Hybrid Battery Control
      Hybrid Battery Current for Hybrid Battery Control (with Correction) Hybrid battery current for hybrid battery control (with correction)
      Hybrid Battery SOC Refer to DATA LIST / ACTIVE TEST
      Refer to DATA LIST / ACTIVE TEST [12/2019 - 11/2023]
      Hybrid Battery Cooling Fan 1 Integrated Airflow Battery cooling blower assembly (No. 0) integrated airflow
      Hybrid/EV Battery Cooling Fan 2 Integrated Airflow Battery cooling blower assembly (No. 1) integrated airflow
      Target Hybrid Battery Temperature Target hybrid battery temperature
      Hybrid Battery Maximum Temperature Highest measured temperature of the HV battery
      Hybrid Battery Minimum Temperature Lowest measured temperature of the HV battery
      Hybrid Battery Cooling Fan Intake Air Temperature 1 Battery cooling blower assembly intake air temperature
      Minimum Voltage of Hybrid Battery Block Lowest battery block voltage
      Maximum Voltage of Hybrid Battery Block Highest battery block voltage
      Hybrid Battery Block Maximum Delta SOC Hybrid battery block maximum delta SOC
      Hybrid Battery Block Maximum Internal Resistance Hybrid battery block maximum internal resistance
      Average of Gradient Road Surface Average of gradient road surface
      WIN Control Limit Power 2 Charge control wattage sent from battery voltage sensor to hybrid vehicle control ECU
      WOUT Control Limit Power 2 Discharge control wattage sent from battery voltage sensor to hybrid vehicle control ECU
      Auxiliary Battery Voltage Refer to DATA LIST / ACTIVE TEST
      Refer to DATA LIST / ACTIVE TEST [12/2019 - 11/2023]
      Auxiliary Battery Current
      Smoothed Value of Auxiliary Battery Temperature
      Auxiliary Battery Voltage at Low Voltage Checking Initiation
      Auxiliary Battery Capacity after IG ON
      Auxiliary Battery Capacity after IG OFF
      Estimated Open Ended Auxiliary Battery Voltage when IG OFF Estimated value of auxiliary battery open circuit voltage when parked
      Auxiliary Battery Charge Rate Rate of auxiliary battery charging
      Auxiliary Battery Charging Rate Accuracy Accuracy of auxiliary battery charging rate
      Low / Middle / High / Disable
      Auxiliary Battery Charging Capacity Full charge capacity of auxiliary battery
      Auxiliary Battery Integrated Current Cumulative auxiliary battery current
      Charging Control Mode Charging control mode of auxiliary battery
      SOC Keep / Auxiliary Charge / Refresh Charge / High/Low Temperature / Abnormal
      Charging Control Ready Status Status of charge control being ready
      Charging Control Working Factor Rate of charging control operation
      Average Vehicle Speed during Trip Average vehicle speed during current trip
      Auxiliary Battery Integrated Current during Trip Cumulative auxiliary battery charging current for the current trip
      Auxiliary Battery Charging Integrated Current when Trip before Last Cumulative auxiliary battery charging current for the previous trip
      Auxiliary Battery Discharging Integrated Current when Trip before Last Cumulative auxiliary battery discharging current for the previous trip
      Auxiliary Battery Average Current during IG OFF Average auxiliary battery current when ignition switch off
      IG OFF Time just before IG ON Number of days ignition switch was off before turned ON
      Auxiliary Battery Average Current when Auxiliary Battery Voltage Low (during IG OFF) Average auxiliary battery current when auxiliary battery voltage low and ignition switch off
      IG OFF Time when Auxiliary Battery Voltage Low (during IG OFF) Number of days ignition switch was off when auxiliary battery low
      Elapsed Time during Auxiliary Battery Voltage Low Time of auxiliary battery being low
      Cruise Vehicle Speed Refer to DATA LIST / ACTIVE TEST (DYNAMIC RADAR CRUISE CONTROL SYSTEM)
      Refer to DATA LIST / ACTIVE TEST [12/2019 - 09/2020] , or refer to DATA LIST / ACTIVE TEST [09/2020 - ]
      Cruise Memory Vehicle Speed
      Cruise Request Throttle Opening Angle
      Cruise Target Acceleration
      Driving Support ECU Target Acceleration
      Cruise Request Driving Force
      Cruise Request Driving Force Feedback Status
      Cruise Control Permission Condition
      Cruise Control Condition
      Cruise Main Switch Operation Condition
      Accelerator Pedal
      Cruise Brake Cancel Switch
      Stop Light Switch Main-CPU
      Stop Light Switch Sub-CPU
      Request Manual Cancel
      Request Automatic Cancel
      Cruise Brake Control Decision
      Cruise Brake Control Permission Condition
  4. CHECK VEHICLE CONTROL HISTORY (SRS AIRBAG) 

    HINT: 

    A part of the control history can be confirmed using the Vehicle Control History.

    Refer to VEHICLE CONTROL HISTORY [12/2019 - 11/2023]