DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Airbag System - Diagnostic Codes (5 Of 7) >> Airbag System >> DTC B00B5-13: Driver Seat Track Position Restraints Sensor Circuit Open [11/2023 - ] >> Procedure

DTC B00B5-13: Driver Seat Track Position Restraints Sensor Circuit Open [11/2023 - ]: Procedure

  1. CHECK CONNECTION OF CONNECTORS 

    Pre-procedure1

    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

      Procedure1

    3. Check that the connectors are properly connected to the airbag sensor assembly and seat position sensor (separate type front seat cushion spring assembly LH).

      OK

      The connectors are properly connected.

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    NG 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    OK 

    See step  2

  2. CHECK CONNECTORS 

    Pre-procedure1

    1. Disconnect the airbag sensor assembly connector.
      GTY1060124Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH)
      *2 Front Seat Inner Belt Assembly LH
      *3 Airbag Sensor Assembly
      *4 Wire Harness
    2. Disconnect the seat position sensor connector.

      Procedure1

    3. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  3

  3. CHECK SEAT POSITION SENSOR CIRCUIT (CHECK FOR OPEN IN THE CIRCUIT) 

    Pre-procedure1

    1. Using a service wire, connect terminals 27 (LSP+) and 24 (GNDL) of connector B.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

      GTY1178546Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH) *2 Front Seat Inner Belt Assembly LH
      *3 Airbag Sensor Assembly *4 Wire Harness
      *5 Service Wire - -
      *a Front view of wire harness connector
      (to Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH))      		 *b Front view of wire harness connector
      (to Airbag Sensor Assembly)

      Procedure1

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      e22-1 (GND) - e22-2 (VS) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    3. Disconnect the service wire from connector B.

    Result: 

    NG 

    See step  6

    Result: 

    OK 

    See step  4

  4. CLEAR DTC 

    Pre-procedure1

    1. Using a service wire, connect terminals 1 (GND) and 2 (VS) of connector G.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

      GTY1177822Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH)
      *2 Front Seat Inner Belt Assembly LH
      *3 Airbag Sensor Assembly
      *4 Wire Harness
      *5 Service Wire
      *a Front view of wire harness connector
      (to Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH))
    2. Connect the airbag sensor assembly connector.
    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

      Procedure1

    5. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

      Result

      Proceed to
      NEXT

      Post-procedure1

    6. Turn the ignition switch off.

    Result: 

    NEXT 

    See step  5

  5. CHECK DTC 

    Pre-procedure1

    1. Turn the ignition switch to ON, and wait for at least 60 seconds.

      Procedure1

    2. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Result Proceed to
      B00B5-13 is output A
      B00B5-13 is not output B

      HINT: 

      Codes other than DTC B00B5-13 may be output at this time, but they are not related to this check.

      Post-procedure1

    3. Turn the ignition switch off.
    4. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    5. Disconnect the service wire from connector G.

    Result: 

    A 

    REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    B 

    REPLACE SEAT POSITION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH). Refer to  REMOVAL [11/2023 - ] 

  6. CHECK CONNECTION OF CONNECTORS 
    1. Check that the connectors are properly connected to the front seat inner belt assembly LH.

      OK

      The connectors are properly connected.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    OK 

    See step  7

  7. CHECK CONNECTORS 

    Pre-procedure1

    1. Disconnect the front seat inner belt assembly LH connector.
      GTY1060318Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH)
      *2 Front Seat Inner Belt Assembly LH
      *3 Airbag Sensor Assembly
      *4 Wire Harness

      Procedure1

    2. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    3. None

    Result: 

    NG 

    REPLACE FRONT SEAT INNER BELT ASSEMBLY LH OR REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (SEAT POSITION SENSOR - FRONT SEAT INNER BELT ASSEMBLY LH) 

    Pre-procedure1

    1. Using a service wire, connect terminals 2 and 1 of connector F.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

      Procedure1

    2. Measure the resistance according to the value(s) in the table below.
      GTY1178633Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH) *2 Front Seat Inner Belt Assembly LH
      *3 Airbag Sensor Assembly *4 Wire Harness
      *5 Service Wire - -
      *a Front view of wire harness connector
      (to Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH))      		 *b Front view of wire harness connector
      (to Front Seat Inner Belt Assembly LH)

      Standard Resistance

      Tester Connection Condition Specified Condition
      e22-2 (VS) - e22-1 (GND) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    3. Disconnect the service wire from connector F.

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - AIRBAG SENSOR ASSEMBLY) 

    Pre-procedure1

    1. Using a service wire, connect terminals 27 (LSP+) and 24 (GNDL) of connector B.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

      Procedure1

    2. Measure the resistance according to the value(s) in the table below.
      GTY1178279Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Seat Position Sensor (Separate Type Front Seat Cushion Spring Assembly LH) *2 Front Seat Inner Belt Assembly LH
      *3 Airbag Sensor Assembly *4 Wire Harness
      *5 Service Wire - -
      *a Front view of wire harness connector
      (to Front Seat Inner Belt Assembly LH)      		 *b Front view of wire harness connector
      (to Airbag Sensor Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      M70-4 (LSP+) - M70-3 (LSP-) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    3. Disconnect the service wire from connector B.

    Result: 

    OK 

    REPLACE FRONT SEAT INNER BELT ASSEMBLY LH. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

Diesel-Data.com