DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Airbag System - Diagnostic Codes (3 Of 7) >> Airbag System >> DTC B0052-13: Passenger Seat Belt Sensor Circuit Open [11/2023 - ] >> Procedure

DTC B0052-13: Passenger Seat Belt Sensor Circuit Open [11/2023 - ]: Procedure

  1. CHECK VEHICLE CONDITION 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      for Manual Seat A
      for Power Seat B

    Result: 

    B 

    See step  7

    Result: 

    A 

    See step  2

  2. CHECK CONNECTION OF CONNECTORS 

    Pre-procedure1

    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

      Procedure1

    3. Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly RH.

      OK

      The connectors are properly connected.

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    NG 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    OK 

    See step  3

  3. CHECK CONNECTORS 

    Pre-procedure1

    1. Disconnect the airbag sensor assembly connector.
      GTY984871Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Inner Belt Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
    2. Disconnect the front seat inner belt assembly RH connector.

      Procedure1

    3. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT) 

    Pre-procedure1

    1. Using a service wire, connect terminals 27 (RBE+) and 18 (GNDR) of connector B.
      GTY1178129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Inner Belt Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *4 Service Wire
      *a Front view of wire harness connector
      (to Front Seat Inner Belt Assembly RH)
      *b Front view of wire harness connector
      (to Airbag Sensor Assembly)
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

      Procedure1

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      e4-1 (+) - e4-2 (-) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    3. Disconnect the service wire from connector B.

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. CLEAR DTC 

    Pre-procedure1

    1. Using a service wire, connect terminals 1 (+) and 2 (-) of connector C.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

      GTY1180003Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Inner Belt Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *4 Service Wire
      *a Front view of wire harness connector
      (to Front Seat Inner Belt Assembly RH)
    2. Connect the airbag sensor assembly connector.
    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

      Procedure1

    5. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

      Result

      Proceed to
      NEXT

      Post-procedure1

    6. Turn the ignition switch off.

    Result: 

    NEXT 

    See step  6

  6. CHECK DTC 

    Pre-procedure1

    1. Turn the ignition switch to ON, and wait for at least 60 seconds.

      Procedure1

    2. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Result Proceed to
      B0052-13 is output A
      B0052-13 is not output B

      HINT: 

      Codes other than DTC B0052-13 may be output at this time, but they are not related to this check.

      Post-procedure1

    3. Turn the ignition switch off.
    4. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    5. Disconnect the service wire from connector C.

    Result: 

    A 

    REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    B 

    REPLACE FRONT SEAT INNER BELT ASSEMBLY RH. Refer to  REMOVAL [11/2023 - ] 

  7. CHECK CONNECTION OF CONNECTORS 

    Pre-procedure1

    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

      Procedure1

    3. Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly RH.

      OK

      The connectors are properly connected.

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    NG 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    OK 

    See step  8

  8. CHECK CONNECTORS 

    Pre-procedure1

    1. Disconnect the airbag sensor assembly connector.
      GTY984871Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Inner Belt Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
    2. Disconnect the front seat inner belt assembly RH connector.

      Procedure1

    3. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN THE CIRCUIT) 

    Pre-procedure1

    1. Using a service wire, connect terminals 27 (RBE+) and 18 (GNDR) of connector B.
      GTY1178289Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Inner Belt Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *4 Service Wire
      *a Front view of wire harness connector
      (to Front Seat Inner Belt Assembly RH)
      *b Front view of wire harness connector
      (to Airbag Sensor Assembly)
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

      Procedure1

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      e28-1 (+) - e28-2 (-) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    3. Disconnect the service wire from connector B.

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  10

  10. CLEAR DTC 

    Pre-procedure1

    1. Using a service wire, connect terminals 1 (+) and 2 (-) of connector C.
      NOTE:

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

      GTY1178646Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Inner Belt Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *4 Service Wire
      *a Front view of wire harness connector
      (to Front Seat Inner Belt Assembly RH)
    2. Connect the airbag sensor assembly connector.
    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

      Procedure1

    5. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

      Result

      Proceed to
      NEXT

      Post-procedure1

    6. Turn the ignition switch off.

    Result: 

    NEXT 

    See step  11

  11. CHECK DTC 

    Pre-procedure1

    1. Turn the ignition switch to ON, and wait for at least 60 seconds.

      Procedure1

    2. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Result Proceed to
      B0052-13 is output A
      B0052-13 is not output B

      HINT: 

      Codes other than DTC B0052-13 may be output at this time, but they are not related to this check.

      Post-procedure1

    3. Turn the ignition switch off.
    4. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    5. Disconnect the service wire from connector C.

    Result: 

    A 

    REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    B 

    REPLACE FRONT SEAT INNER BELT ASSEMBLY RH. Refer to  REMOVAL [11/2023 - ] 

Diesel-Data.com