Data List / Active Test [11/2023 - ]
- DATA LIST NOTE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- Read the Data List according to the display on the GTS.
Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Open Switch OPEN switch signal OFF or ON OFF: OPEN switch not pressed
ON: OPEN switch pressed- Close Switch CLOSE switch signal OFF or ON OFF: CLOSE switch not pressed
ON: CLOSE switch pressed- Up Switch UP switch signal OFF or ON OFF: UP switch not pressed
ON: UP switch pressed- Down Switch DOWN switch signal OFF or ON OFF: DOWN switch not pressed
ON: DOWN switch pressed- Front SW Auto Operation Sliding roof auto operation function OFF or ON Customize setting displayed - Hall IC1 Pulse Hall IC1 pulse output Lo or Hi Lo and Hi repeat during motor operation Lo: Hall IC1 output is low
Hi: Hall IC1 output is highHall IC1 Status Status of Hall IC1 Normal or Error Normal: Hall IC1 normal
Error: Hall IC1 not normal- Hall IC2 Pulse Hall IC2 pulse output Lo or Hi Lo and Hi repeat during motor operation Lo: Hall IC2 output is low
Hi: Hall IC2 output is highHall IC2 Status Status of Hall IC2 Normal or Error Normal: Hall IC2 normal
Error: Hall IC2 not normal- Ignition (MPX) Ignition switch signal (LIN signal) OFF or ON OFF: Ignition switch off
ON: Ignition switch ON- Door Key Close Operation Key-linked sliding roof close signal OFF or ON OFF: Driver door key cylinder not turned
ON: Driver door key cylinder turned and held at the lock position- Door Key Open Operation Key-linked sliding roof open signal OFF or ON OFF: Driver door key cylinder not turned
ON: Driver door key cylinder turned and held at the unlock position- Wireless Open Operation Wireless transmitter-linked sliding roof open signal OFF or ON OFF: Electrical key transmitter sub-assembly UNLOCK switch not pressed
ON: Electrical key transmitter sub-assembly UNLOCK switch pressed and held- Key Off Permission Key-off sliding roof operation permit signal OFF or ON OFF: Any status except "ON" status
ON: Front doors are not opened within 45 seconds after ignition switch turned off- Door Key Related Operation Key-linked sliding roof open function operating direction Slide or Tilt Customize setting displayed - Wireless Key Rel Operation Wireless transmitter-linked sliding roof open function operating direction Slide or Tilt Customize setting displayed - Open Switch Failure (Past) Open switch failure signal (Past) OFF or ON OFF: No sliding roof open switch failure signal (Past)
ON: Sliding roof open switch failure signal (Past)- Close Switch Failure (Past) Close switch failure signal (Past) OFF or ON OFF: No sliding roof close switch failure signal (Past)
ON: Sliding roof close switch failure signal (Past)- Up Switch Failure (Past) Up switch failure signal (Past) OFF or ON OFF: No sliding roof tilt up switch failure signal (Past)
ON: Sliding roof tilt up switch failure signal (Past)- Down Switch Failure (Past) Down switch failure signal (Past) OFF or ON OFF: No sliding roof tilt down switch failure signal (Past)
ON: Sliding roof tilt down switch failure signal (Past)- Open Switch Failure (Current) Open switch failure signal (Current) OFF or ON OFF: No sliding roof open switch failure signal (Current)
ON: Sliding roof open switch failure signal (Current)- Close Switch Failure (Current) Close switch failure signal (Current) OFF or ON OFF: No sliding roof close switch failure signal (Current)
ON: Sliding roof close switch failure signal (Current)- Up Switch Failure (Current) Up switch failure signal (Current) OFF or ON OFF: No sliding roof tilt up switch failure signal (Current)
ON: Sliding roof tilt up switch failure signal (Current)- Down Switch Failure (Current) Down switch failure signal (Current) OFF or ON OFF: No sliding roof tilt down switch failure signal (Current)
ON: Sliding roof tilt down switch failure signal (Current)- Number of Trouble Codes Number of DTCs Min.: 0, Max.: 255 Number of stored DTCs - Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note FR Door Courtesy Switch Status Front door courtesy light switch (RH) signal Close or Open Close: Front door RH closed
Open: Front door RH open- FL Door Courtesy Switch Status Front door courtesy light switch (LH) signal Close or Open Close: Front door LH closed
Open: Front door LH open- IGR Power Ignition switch ON signal OFF or ON OFF: Ignition switch off or ACC
ON: Ignition switch ON- Communication Slide Roof Connection status between sliding roof ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) STOP or OK STOP: Communication stopped
OK: Normal communication- Door Key P/W Up Function Key-linked power windows and sliding roof close function Disable or Enable Customize setting displayed - Door Key P/W Down Function Key-linked power windows and sliding roof open function Disable or Enable Customize setting displayed - P/W Down W/ Transmit Function Wireless transmitter-linked power windows and sliding roof open function Disable or Enable Customize setting displayed - Slide Roof Open Warning Function Sliding roof open warning function OFF or ON Customize setting displayed -
- Read the Data List according to the display on the GTS.
- ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.