DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Occupant Classification System - Diagnostic Codes & Symptom Tests >> Occupant Classification System >> LIN Communication Circuit [11/2023 - ] >> Procedure

LIN Communication Circuit [11/2023 - ]: Procedure

  1. CHECK ERROR CODE 
    1. Check the Error Code.

      Result

      Result Proceed to
      Error code 17 is output A
      Error code 18 is output B
      Error code 17 and 18 are output C

    Result: 

    B 

    See step  7

    Result: 

    C 

    See step  12

    Result: 

    A 

    See step  2

  2. CHECK CONNECTION OF CONNECTORS 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check that the connectors are properly connected to the airbag sensor assembly and separate type front seat cushion spring assembly RH (front occupant classification sensor LH).

      OK

      The connectors are properly connected.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    OK 

    See step  3

  3. CHECK CONNECTORS 
    1. Disconnect the airbag sensor assembly connector.
      GTY984871Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Separate Type Front Seat Cushion Spring Assembly RH (Front Occupant Classification Sensor LH)
      *2 Airbag Sensor Assembly
      *3 Wire Harness
    2. Disconnect the separate type front seat cushion spring assembly RH (front occupant classification sensor LH) connector.
    3. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M10-24 (SVC) - e5-1 (SVC) Always Below 1 Ω
      M10-32 (SIG) - e5-2 (SIG) Always Below 1 Ω
      M10-31 (SGD) - e5-3 (SGD) Always Below 1 Ω
      GTY1178456Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Separate Type Front Seat Cushion Spring Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
      *b Front view of wire harness connector
      (to Separate Type Front Seat Cushion Spring Assembly RH (Front Occupant Classification Sensor LH))

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH 
    1. Connect the airbag sensor assembly connector.
    2. Replace the separate type front seat cushion spring assembly RH with a new one.

      for Manual Seat: Refer to REMOVAL [11/2023 - ]

      for Power Seat: Refer to REMOVAL [11/2023 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  6

  6. PERFORM ZERO POINT CALIBRATION 
    1. Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

      Refer to INITIALIZATION [11/2023 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    END 

  7. CHECK CONNECTION OF CONNECTORS 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check that the connectors are properly connected to the airbag sensor assembly and separate type front seat cushion spring assembly RH (rear occupant classification sensor LH).

      OK

      The connectors are properly connected.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    OK 

    See step  8

  8. CHECK CONNECTORS 
    1. Disconnect the airbag sensor assembly connector.
      GTY984871Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Separate Type Front Seat Cushion Spring Assembly RH (Rear Occupant Classification Sensor LH)
      *2 Airbag Sensor Assembly
      *3 Wire Harness
    2. Disconnect the separate type front seat cushion spring assembly RH (rear occupant classification sensor LH) connector.
    3. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M10-24 (SVC) - e6-1 (SVC) Always Below 1 Ω
      M10-32 (SIG) - e6-2 (SIG) Always Below 1 Ω
      M10-31 (SGD) - e6-3 (SGD) Always Below 1 Ω
      GTY1178455Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Separate Type Front Seat Cushion Spring Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
      *b Front view of wire harness connector
      (to Separate Type Front Seat Cushion Spring Assembly RH (Rear Occupant Classification Sensor LH))

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  10

  10. REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH 
    1. Connect the airbag sensor assembly connector.
    2. Replace the separate type front seat cushion spring assembly RH with a new one.

      for Manual Seat: Refer to REMOVAL [11/2023 - ]

      for Power Seat: Refer to REMOVAL [11/2023 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  11

  11. PERFORM ZERO POINT CALIBRATION 
    1. Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

      Refer to INITIALIZATION [11/2023 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    END 

  12. CHECK CONNECTION OF CONNECTORS 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check that the connectors are properly connected to the airbag sensor assembly and separate type front seat cushion spring assembly RH.

      OK

      The connectors are properly connected.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    OK 

    See step  13

  13. CHECK CONNECTORS 
    1. Disconnect the airbag sensor assembly connector.
      GTY985316Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Separate Type Front Seat Cushion Spring Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
    2. Disconnect the separate type front seat cushion spring assembly RH connector.
    3. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  14

  14. CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M10-24 (SVC) - e5-1 (SVC) Always Below 1 Ω
      M10-24 (SVC) - e6-1 (SVC) Always Below 1 Ω
      M10-32 (SIG) - e5-2 (SIG) Always Below 1 Ω
      M10-32 (SIG) - e6-2 (SIG) Always Below 1 Ω
      M10-31 (SGD) - e5-3 (SGD) Always Below 1 Ω
      M10-31 (SGD) - e6-3 (SGD) Always Below 1 Ω
      GTY1177865Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Separate Type Front Seat Cushion Spring Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
      *b Front view of wire harness connector
      (to Separate Type Front Seat Cushion Spring Assembly RH (Front Occupant Classification Sensor LH))
      *c Front view of wire harness connector
      (to Separate Type Front Seat Cushion Spring Assembly RH (Rear Occupant Classification Sensor LH))

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  15

  15. CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M10-32 (SIG) - Other terminals and body ground Always 10 kΩ or higher
      e5-2 (SIG) - Other terminals and body ground Always 10 kΩ or higher
      e6-2 (SIG) - Other terminals and body ground Always 10 kΩ or higher
      GTY1177866Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Separate Type Front Seat Cushion Spring Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
      *b Front view of wire harness connector
      (to Separate Type Front Seat Cushion Spring Assembly RH (Front Occupant Classification Sensor LH))
      *c Front view of wire harness connector
      (to Separate Type Front Seat Cushion Spring Assembly RH (Rear Occupant Classification Sensor LH))

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  16

  16. CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY RH) 
    1. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
      GTY1177866Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Separate Type Front Seat Cushion Spring Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *a Front view of wire harness connector
      (to Airbag Sensor Assembly)
      *b Front view of wire harness connector
      (to Separate Type Front Seat Cushion Spring Assembly RH (Front Occupant Classification Sensor LH))
      *c Front view of wire harness connector
      (to Separate Type Front Seat Cushion Spring Assembly RH (Rear Occupant Classification Sensor LH))
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      M10-32 (SIG) - Body ground Ignition switch ON Below 1 V
      e5-2 (SIG) - Body ground Ignition switch ON Below 1 V
      e6-2 (SIG) - Body ground Ignition switch ON Below 1 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  17

  17. REPLACE AIRBAG SENSOR ASSEMBLY 
    1. Connect the separate type front seat cushion spring assembly RH connector.
    2. Replace the airbag sensor assembly with a new one.

      Refer to REMOVAL [11/2023 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  18

  18. PERFORM ZERO POINT CALIBRATION 
    1. Using the GTS, perform "Occupant Detection Sensor Zero Point Calibration".

      Refer to INITIALIZATION [11/2023 - ]

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    END 

Diesel-Data.com