Data List / Active Test [11/2023 - ]
- DATA LIST
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- According to the display on the GTS, read the Data List.
Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Total Distance Traveled Total distance traveled 0 to 16777215 Same as actual total distance traveled For the unit, refer to "Total Distance Traveled - Unit" Total Distance Traveled - Unit Total Distance Traveled - unit km or mile km: km
mile: mile- Back Door Lock Status Back door condition signal Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked- Half Latch Switch Latch switch signal ON or OFF ON: When in the open latch or overstroke position
OFF: Half latch position → full latch position- Closer Position Switch Initial switch signal ON or OFF ON: Back door lock sector gear in center position (Initial switch on)
OFF: Back door lock sector gear out of center position (Initial switch off)- Pawl Switch Pawl switch signal ON or OFF ON: Back door lock motor open-latched
OFF: Back door lock motor except open latched- Courtesy Switch Back door courtesy switch signal ON or OFF ON: Open latch position → half latch position
OFF: Full latch position → overstroke position- PBD Main Switch Power back door ON/OFF signal ON or OFF Current customize setting displayed - PBD Close Switch No. 1 power back door control switch signal ON or OFF ON: No. 1 power back door control switch pushed
OFF: No. 1 power back door control switch not pushed- IG Switch Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off"OFF" is also displayed for this item when the ignition switch to ACC Kick Sensor Function Status of the hands free power back door function ON or OFF ON: Hands free power back door ON
OFF: Hands free power back door offw/ Hands Free Power Back Door Door Lock Signal Back door condition signal Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked- Status of Kick Sensor Detection Status of the kick door control sensor ON or OFF ON: Kick door control sensor ON
OFF: Kick door control sensor offw/ Hands Free Power Back Door Status of Kick Sensor Abnormal Status of the kick door control sensor error Normal or Abnormal Normal: Kick door control sensor is normal
Abnormal: Kick door control sensor is abnormalw/ Hands Free Power Back Door Kick Sensor Installation Status of the kick door control sensor connection ON or OFF ON: Kick door control sensor equipped
OFF: Kick door control sensor not equippedw/ Hands Free Power Back Door PBD Touch Sensor RH Power back door sensor assembly RH signal ON, OFF or Open ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed
Open: Power back door sensor assembly RH circuit open- PBD Touch Sensor LH Power back door sensor assembly LH signal ON, OFF or Open ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed
Open: Power back door sensor assembly LH circuit open- Correction of Back Door Position Correction of back door position Not Complied With or Complied With Not Complied With: not complied with
Complied With: complied with- PBD Close Switch Operation History No. 1 power back door control switch operation history ON or OFF ON: Has operation history
OFF: No operation historyThe operation history will be cleared by disconnecting the cable from the negative (-) terminal of the auxiliary battery for approximately 30 seconds. Kick Sensor Operation History Hands free power back door operation history ON or OFF ON: Has operation history
OFF: No operation history- The operation history will be cleared by disconnecting the cable from the negative (-) terminal of the auxiliary battery for approximately 30 seconds.
- w/ Hands Free Power Back Door
Opened Number of Times Number of times for back door opened 0 to 2147483647 Number of times for back door opened - Closed Number of Times Number of times for back door closed 0 to 2147483647 Number of times for back door closed - PBD SW Operating Condition Setting No. 1 power back door control switch or power back door control switch operation Short Press (0.04s) or Long Press (0.8s) Current customize setting displayed - PBD Buzzer Function Status of the power back door buzzer ON or OFF Current customize setting displayed - PBD Assist Close Function Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. ON or OFF Current customize setting displayed - PBD Assist Open Function Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated. ON or OFF Current customize setting displayed - PBD Door Unlock with One Motion Setting Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly). Back Door or All Doors Current customize setting displayed - PBD Wireless Function Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). ON or OFF Current customize setting displayed - PBD Wireless One Motion Function Wireless one motion setting condition ON or OFF Current customize setting displayed - PBD Wireless SW Setting Wireless operation setting condition 1 Time Press, 2 Times Press or Long Press (0.8s) Current customize setting displayed - PBD Kick-in Beep Sound Function that sounds a buzzer when a kick operation detected. ON or OFF Current customize setting displayed w/ Hands Free Power Back Door Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Back Door Lock Position Status Back door lock position signal Lock or Unlock Lock: Back door locked
Unlock: Back door unlocked- Back Door Operation Switch (Instrument) Power back door control switch signal ON or OFF ON: Power back door control switch on
OFF: Power back door control switch off-
- According to the display on the GTS, read the Data List.
- ACTIVE TEST
HINT:
Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- According to the display on GTS perform the "Active Test".
Body Electrical > Back Door > Active Test
Tester Display Measurement Item Control Range Diagnostic Note PBD Motor (Open) Power back door motor operation Start - PBD Motor (Close) Power back door motor operation Start - PBD Buzzer (Small Volume) Power back door warning buzzer sound (small volume) Start - PBD Buzzer (Middle Volume) Power back door warning buzzer sound (Middle volume) Start - PBD Buzzer (Large Volume) Power back door warning buzzer sound (Large volume) Start - PBD Release Closer Latch release operation Start - Courtesy Lamp Back door courtesy light operation Start -
- According to the display on GTS perform the "Active Test".