DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Electrical >> Gauges >> Meter / Gauge System (Except 12.3 Inch Display) - Symptom Tests (2 Of 2) & Circuit Tests >> METER / GAUGE SYSTEM (except 12.3 Inch Display) >> Steering Pad Switch Circuit [10/2022 - ] >> Procedure

Steering Pad Switch Circuit [10/2022 - ]: Procedure

  1. INSPECT STEERING PAD SWITCH ASSEMBLY 
    1. Remove the steering pad switch assembly.

      Refer to REMOVAL [10/2022 - 11/2023] , or refer to REMOVAL [11/2023 - ]

    2. Inspect the steering pad switch assembly.

      Refer to INSPECTION [12/2019 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE STEERING PAD SWITCH ASSEMBLY. Refer to  REMOVAL [10/2022 - 11/2023]  , or refer to  REMOVAL [11/2023 - ] 

    Result: 

    OK 

    See step  2

  2. INSPECT SPIRAL CABLE SUB-ASSEMBLY 
    1. Remove the spiral cable sub-assembly.

      Refer to REMOVAL [10/2022 - 11/2023] , or refer to REMOVAL [11/2023 - ]

    2. Inspect the spiral cable sub-assembly.

      Refer to INSPECTION [12/2019 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE SPIRAL CABLE SUB-ASSEMBLY. Refer to  REMOVAL [10/2022 - 11/2023]  , or refer to  REMOVAL [11/2023 - ] 

    Result: 

    OK 

    See step  3

  3. CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE) 
    GTY888908Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Spiral Cable Sub-assembly)
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      H24-10 (+DP2) - Body ground Ignition switch ON 4.8 to 5.2 V
      H24-11 (+DP) - Body ground Ignition switch ON 4.8 to 5.2 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  5

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND) 
    1. Disconnect the H107 radio and display receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H107-20 (SWG) - H24-4 (EAU) Always Below 1 Ω
      H107-1 (GND1) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2022 - 11/2023]  , or refer to  REMOVAL [11/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY) 
    1. Disconnect the H21 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H24-10 (+DP2) - H21-28 (MSM+) Always Below 1 Ω
      H24-11 (+DP) - H21-29 (MSTI) Always Below 1 Ω
      H24-10 (+DP2) or H21-28 (MSM+) - Body ground Always 10 kΩ or higher
      H24-11 (+DP) or H21-29 (MSTI) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2019 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

Diesel-Data.com