DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Monitor System - Service Information >> ULTRASONIC SENSOR (for Rear) >> Removal [11/2023 - ] >> Procedure

Removal [11/2023 - ]: Procedure

  1. REMOVE REAR BUMPER ASSEMBLY 

    Refer to REMOVAL [11/2023 - ]

  2. REMOVE REAR CENTER ULTRASONIC SENSOR 

    HINT: 

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.

    1. Disconnect the connector.
      GTY846393Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws and remove the rear center ultrasonic sensor as shown in the illustration.
      GTY841318Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  3. REMOVE REAR CORNER ULTRASONIC SENSOR 

    HINT: 

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.

    1. Disconnect the connector.
      GTY846429Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws and remove the rear corner ultrasonic sensor as shown in the illustration.
      GTY935537Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  4. REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER 

    HINT: 

    • Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.
    • When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.
    • The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
    1. Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

      Heating Temperature

      Item Temperature
      Rear Bumper Assembly 40 to 60°C (104 to 140°F)
      Rear Center Ultrasonic Sensor Retainer
      WARNING:
      • Do not touch the heat light and heated parts.
      • Touching the heat light may result in burns.
      • Touching heated parts for a long time may result in burns.
      GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Heated Part
      *b Heat Light
    2. Remove the rear center ultrasonic sensor retainer.
      GTY846395Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER 

    HINT: 

    • Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.
    • When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.
    • The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
    1. Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

      Heating Temperature

      Item Temperature
      Rear Bumper Assembly 40 to 60°C (104 to 140°F)
      Rear Corner Ultrasonic Sensor Retainer
      WARNING:
      • Do not touch the heat light and heated parts.
      • Touching the heat light may result in burns.
      • Touching heated parts for a long time may result in burns.
      GTY583249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Heated Part
      *b Heat Light
    2. Remove the rear corner ultrasonic sensor retainer.
      GTY928000Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE ULTRASONIC SENSOR CUSHION SET 

    HINT: 

    Only perform this procedure when removing and installing the ultrasonic sensor cushion set.

    1. Remove the ultrasonic sensor cushion set as shown in the illustration.
      GTY866906Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
Diesel-Data.com