DTC B15D5: Rear Seat Entertainment System Disconnected [12/2019 - 10/2022]: Procedure

1. Check that optional components (including associated wiring) which generate radio waves are not installed.

   Result

   Result	Proceed to
   Optional components (including associated wiring) are installed.	A
   Optional components (including associated wiring) are not installed.	B

   HINT: 

   • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
   • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.

Result: 

B 

See step  3

Result: 

A 

See step  2

1. Remove optional components (including associated wiring).
   NOTE:

   Do not remove optional components or associated wiring without the permission of the customer.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Clear the DTCs.

   Body Electrical > Navigation System > Clear DTCs 

2. Recheck for DTCs and check that no DTCs are output.

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END 

Result: 

NG 

See step  4

1. Disconnect the R16 television display assembly connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R16-17 (GND) - Body ground	Always	Below 1 Ω

3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Condition	Specified Condition
   R16-1 (+B) - R16-17 (GND)	Always*1 Ignition switch off*2	11 to 14 V*3 10.5 to 16 V*4
   R16-2 (ACC) - R16-17 (GND)	Ignition switch ACC	11 to 14 V*3 10.5 to 16 V*4

   *1: for Gasoline Model

   *2: for HV Model

   *3: w/o Stop and Start System

   *4: w/ Stop and Start System

   Result

   Result	Proceed to
   OK (for 8 Inch Display)	A
   OK (for 12.3 Inch Display)	B
   NG (w/o Stop and Start System)	C
   NG (w/ Stop and Start System)	D

Result: 

B 

See step  7

Result: 

C 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

D 

GO TO STOP AND START SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2019 - 10/2022] 

Result: 

A 

See step  5

1. Disconnect the H1 radio and display receiver assembly connector.
2. Disconnect the R16 television display assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R16-4 (TX+) - H1-19 (TX+)	Always	Below 1 Ω
   R16-5 (TX-) - H1-20 (TX-)	Always	Below 1 Ω
   R16-4 (TX+) or H1-19 (TX+) - Body ground	Always	10 kΩ or higher
   R16-5 (TX-) or H1-20 (TX-) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  6

1. Replace the television display assembly with a new or known good one.

   Refer to REMOVAL [12/2019 - 10/2022]

2. Clear the DTCs.

   Body Electrical > Navigation System > Clear DTCs 

3. Recheck for DTCs and check that no DTCs are output.

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (TELEVISION DISPLAY ASSEMBLY WAS DEFECTIVE) 

Result: 

NG 

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [12/2019 - 10/2022] 

1. Disconnect the H4 radio receiver assembly connector.
2. Disconnect the R16 television display assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R16-4 (TX+) - H4-19 (TX+)	Always	Below 1 Ω
   R16-5 (TX-) - H4-20 (TX-)	Always	Below 1 Ω
   R16-4 (TX+) or H4-19 (TX+)- Body ground	Always	10 kΩ or higher
   R16-5 (TX-) or H4-20 (TX-) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

Result: 

OK 

See step  8

1. Replace the television display assembly with a new or known good one.

   Refer to REMOVAL [12/2019 - 10/2022]

2. Clear the DTCs.

   Body Electrical > Navigation System > Clear DTCs 

3. Recheck for DTCs and check that no DTCs are output.

   Body Electrical > Navigation System > Trouble Codes 

   OK

   No DTCs are output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (TELEVISION DISPLAY ASSEMBLY WAS DEFECTIVE) 

Result: 

NG 

REPLACE RADIO RECEIVER ASSEMBLY. Refer to  REMOVAL [12/2019 - 10/2022]