DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Restraints >> Restraints Control Systems >> Pre-Collision System - Diagnostics - Introduction >> Pre-Collision System >> Data List / Active Test [12/2019 - 09/2020] >> Data List / Active Test [12/2019 - 09/2020]

Data List / Active Test [12/2019 - 09/2020]

  1. DATA LIST 
    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT: 

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Body Electrical / Pre-Collision System / Data List.
    5. Read the Data List according to the display on the GTS.

      Body Electrical > Pre-Collision System > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Total Distance Traveled - - - Cannot be used
      Total Distance Traveled - Unit - - - Cannot be used
      PCS Function ON/OFF State Pre-collision system status ON / OFF ON: Pre-collision system enabled
      OFF: Pre-collision system disabled      		 -
      PBA Request Pre-collision brake assist operation status Not PBA Request / PBA Standby Request / PBA Request Level 1 / PBA Request Level 2 Not PBA Request: Pre-collision brake assist not requested
      PBA Standby Request: Low pre-collision brake assist requested
      PBA Request Level 1: Medium pre-collision brake assist requested
      PBA Request Level 2: High pre-collision brake assist requested      		 The value changes in accordance with the possibility of a collision. This item indicates the pre-collision brake assist standby status. Whether pre-collision brake assist is applied or not is determined by the depression of the brake pedal.
      VGRS Activation Request - - - Cannot be used
      Warning Brake Request - - - Cannot be used
      FPB Request Skid control ECU PCS brake request (pre-braking) OFF / ON OFF: Not operating
      ON: Operating      		 -
      PB Request Pre-collision brake request status OFF / ON OFF: Not operating
      ON: Operating      		 -
      AVS Control Request - - - Cannot be used
      Prefill Skid control ECU PCS brake assist standby OFF / ON OFF: Not operating
      ON: Operating      		 -
      PBR Request PBR operation status OFF / ON OFF: Not operating
      ON: Operating      		 -
      PBH Request PBH operation status OFF / ON OFF: Not operating
      ON: Operating      		 -
      PCS PBA Invalid PCS PBA status OFF / ON OFF: Valid
      ON: Invalid      		 -
      PCS Warning Buzzer Invalid PCS warning buzzer status OFF / ON OFF: Valid
      ON: Invalid      		 -
      PCS PB Invalid PCS PB Status OFF / ON OFF: Valid
      ON: Invalid      		 -
      PCS Warning Display Request PCS warning sensitivity displayed on multi-information display Not Request / PCS Warning Display 1 Request / PCS Warning Display 2 Request / PCS Warning Display 3 Request Not Request: No message
      PCS Warning Display 1 Request: Warning sensitivity (early) displayed
      PCS Warning Display 2 Request: Warning sensitivity (middle) displayed
      PCS Warning Display 3 Request: Warning sensitivity (late) displayed      		 -
      PCS Warning Buzzer Request PCS meter buzzer operation status OFF / ON OFF: Not sounding
      ON: Sounding      		 -
      Vehicle Information (Conv/HV) Vehicle information (Conv/HV) Unknown / Conv / HV Unknown: Vehicle information not confirmed
      Conv: Conventional
      HV: Hybrid vehicle      		 -
      PCS Function ON/OFF State Stored Pre-collision system on/off setting when the pre-collision system is turned off and the ignition switch is turned off and then to ON. Not Stored / Stored Not Stored: Defaults to on
      Stored: Maintains last on/off status      		 "PCS Function ON/OFF State Stored" is a customizable item which can be set using the GTS.
      PCS Warning Timing State Stored 2 Sensitivity setting of the pre-collision system when the pre-collision system is turned on and the ignition switch is turned off and then to ON. Not Stored / Stored Not Stored: Defaults to middle
      Stored: Maintains last setting      		 "PCS Warning Timing State Stored 2" is a customizable item which can be set using the GTS.
      PCS Warning Timing State Stored 3 Sensitivity setting when the pre-collision system is turned off and the ignition switch is turned off and then to ON. Not Stored / Stored Not Stored: Defaults to middle
      Stored: Maintains last setting      		 "PCS Warning Timing State Stored 3" is a customizable item which can be set using the GTS.
      PCS Warning Timing State Stored 1 Sensitivity setting of the pre-collision system when the pre-collision system is turned off and then on with the ignition switch ON. Not Stored / Stored Not Stored: Defaults to middle
      Stored: Maintains last setting      		 "PCS Warning Timing State Stored 1" is a customizable item which can be set using the GTS.
  2. ACTIVE TEST 

    HINT: 

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Body Electrical / Pre-Collision System / Active Test.
    5. Perform the Active Test according to the display on the GTS.

      Body Electrical > Pre-Collision System > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      PCS Warning Buzzer Sounds the meter buzzer Start / Stop Test possible with ignition switch ON, vehicle stopped
Diesel-Data.com