DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (2GR-FKS) - Diagnostic Codes (1 Of 6) >> SFI System >> DTC P0100-12: Mass or Volume Air Flow Sensor "A" Circuit Short to Battery; DTC P0100-14: Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open [12/2019 - 10/2022] >> Procedure

DTC P0100-12: Mass or Volume Air Flow Sensor "A" Circuit Short to Battery; DTC P0100-14: Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open [12/2019 - 10/2022]: Procedure

  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY) 
    GTY888639Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Mass Air Flow Meter Sub-assembly)
    1. Disconnect the mass air flow meter sub-assembly connector.
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      C30-3 (VCC) - C30-2 (E2G) Ignition switch ON 4.8 to 5.2 V
      C30-1 (FG) - C30-2 (E2G) Ignition switch ON 4.8 to 5.2 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  5

    Result: 

    OK 

    See step  2

  2. REPLACE MASS AIR FLOW METER SUB-ASSEMBLY 

    Refer to REMOVAL [12/2019 - 10/2022]

    HINT: 

    Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

    Refer to INITIALIZATION [12/2019 - 10/2022]

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  3

  3. CLEAR DTC 
    1. Clear the DTCs.

      Powertrain > Engine > Clear DTCs 

    2. Turn the ignition switch off and wait for at least 30 seconds.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  4

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P0100-12 OR P0100-14) 
    1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
    2. Read the DTCs.

      Powertrain > Engine > Trouble Codes 

      Result

      Result Proceed to
      DTCs are not output A
      DTC P0100-12 or P0100-14 is output B

    Result: 

    A 

    END 

    Result: 

    B 

    REPLACE ECM 

    Refer to REMOVAL [12/2019 - 09/2020] , or refer to REMOVAL [09/2020 - 10/2022]

  5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) 
    1. Disconnect the mass air flow meter sub-assembly connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C30-3 (VCC) - C54-90 (VC) Always Below 1 Ω
      C30-1 (FG) - C54-116 (VG) Always Below 1 Ω
      C30-2 (E2G) - C54-115 (E2G) Always Below 1 Ω
      C30-3 (VCC) or C54-90 (VC) - Body ground and other terminals Always 10 kΩ or higher
      C30-1 (FG) or C54-116 (VG) - Body ground and other terminals Always 10 kΩ or higher
      C30-2 (E2G) or C54-115 (E2G) - Body ground and other terminals Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM 

    Refer to REMOVAL [12/2019 - 09/2020] , or refer to REMOVAL [09/2020 - 10/2022]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

Diesel-Data.com