Rear Power Window RH does not Operate with Rear Power Window Switch RH [12/2019 - 11/2023]: Procedure

1. Read the Data List according to the display on the GTS.

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Communication RR-Door Motor	Connection status between power window regulator motor assembly (for rear RH door) and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Communication stopped OK: Normal communication	-

   Body Electrical > Main Body > Data List 

   Tester Display
   Communication RR-Door Motor

   OK

   OK is displayed for each Data List item above.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting). Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2019 - 11/2023] 

Result: 

OK 

See step  2

1. Read the Data List according to the display on the GTS.

   Body Electrical > RR-Door Motor > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   RR Door P/W Up SW	Rear RH door power window manual up switch signal	OFF or ON	OFF: Rear RH door power window manual up switch not being operated ON: Rear RH door power window manual up switch being operated	-
   RR Door P/W Down SW	Rear RH door power window manual down switch signal	OFF or ON	OFF: Rear RH door power window manual down switch not being operated ON: Rear RH door power window manual down switch being operated	-

   Body Electrical > RR-Door Motor > Data List 

   Tester Display
   RR Door P/W Up SW
   RR Door P/W Down SW

   OK

   On the GTS screen, ON or OFF is displayed accordingly.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  4

Result: 

OK 

See step  3

1. Perform the Active Test according to the display on the GTS.
   WARNING:

   Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

   Body Electrical > RR-Door Motor > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   Power Window	Power window	OFF / DOWN / UP	-

   Body Electrical > RR-Door Motor > Active Test 

   Tester Display
   Power Window

   OK

   Rear RH door power window operates normally.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [12/2019 - 10/2022]  , or refer to  REMOVAL [10/2022 - 11/2023] 

Result: 

NG 

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door). Refer to  REMOVAL [12/2019 - 10/2022]  , or refer to  REMOVAL [10/2022 - 11/2023] 

Refer to INSPECTION [12/2019 - ]

Result

Result: 

NG 

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door). Refer to  REMOVAL [12/2019 - ] 

Result: 

OK 

See step  5

1. Disconnect the K4 power window regulator motor assembly (for rear RH door) connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   K2-5 (UP) - K4-10 (UP)	Always	Below 1 Ω
   K2-5 (UP) or K4-10 (UP) - Body ground	Always	10 kΩ or higher
   K2-4 (DOWN) - K4-7 (DOWN)	Always	Below 1 Ω
   K2-4 (DOWN) or K4-7 (DOWN) - Body ground	Always	10 kΩ or higher
   K2-7 (GND) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door). Refer to  REMOVAL [12/2019 - 10/2022]  , or refer to  REMOVAL [10/2022 - 11/2023] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR