DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Accessories & Equipment >> Mirrors >> Power Mirror Control System (W/ Memory) - Diagnostics - Introduction >> POWER MIRROR CONTROL SYSTEM (w/ Memory) >> Data List / Active Test [11/2023 - ] >> Data List / Active Test [11/2023 - ]

Data List / Active Test [11/2023 - ]

  1. DATA LIST 
    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT: 

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Read the Data List according to the display on the GTS.

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Outer Mirror Fold Switch Retractable outer mirror switch signal OFF or ON OFF: Retractable outer mirror switch not in retract position
      ON: Retractable outer mirror switch in retract position      		 -
      Outer Mirror Auto Switch Retractable outer mirror switch signal OFF or ON OFF: Retractable outer mirror switch not in auto position
      ON: Retractable outer mirror switch in auto position      		 -
      Outer Mirror Control Switch (RH Select) Mirror select switch signal for RH mirror OFF or ON OFF: Mirror select switch off
      ON: Mirror select switch R switch on      		 -
      Outer Mirror Control Switch (LH Select) Mirror select switch signal for LH mirror OFF or ON OFF: Mirror select switch off
      ON: Mirror select switch L switch on      		 -
      Outer Mirror Control Switch (Surface Adjust Right) Mirror adjust switch signal (Right) OFF or ON OFF: Mirror adjust switch not pushed right
      ON: Mirror adjust switch pushed right      		 -
      Outer Mirror Control Switch (Surface Adjust Left) Mirror adjust switch signal (Left) OFF or ON OFF: Mirror adjust switch not pushed left
      ON: Mirror adjust switch pushed left      		 -
      Outer Mirror Control Switch (Surface Adjust Up) Mirror adjust switch signal (Up) OFF or ON OFF: Mirror adjust switch not pushed up
      ON: Mirror adjust switch pushed up      		 -
      Outer Mirror Control Switch (Surface Adjust Down) Mirror adjust switch signal (Down) OFF or ON OFF: Mirror adjust switch not pushed down
      ON: Mirror adjust switch pushed down      		 -
      MEM Switch No. with Key ID 1 Switch linked with key ID1 NONE, D MEM SW1, D MEM SW2, or D MEM SW3 NONE: No switches linked with key ID1
      D MEM SW1: M1 linked with key ID1
      D MEM SW2: M2 linked with key ID1
      D MEM SW3: M3 linked with key ID1*      		 -
      MEM Switch No. with Key ID 2 Switch linked with key ID2 NONE, D MEM SW1, D MEM SW2, or D MEM SW3 NONE: No switches linked with key ID2
      D MEM SW1: M1 linked with key ID2
      D MEM SW2: M2 linked with key ID2
      D MEM SW3: M3 linked with key ID2*      		 -
      MEM Switch No. with Key ID 3 Switch linked with key ID3 NONE, D MEM SW1, D MEM SW2, or D MEM SW3 NONE: No switches linked with key ID3
      D MEM SW1: M1 linked with key ID3
      D MEM SW2: M2 linked with key ID3
      D MEM SW3: M3 linked with key ID3*      		 -
      MEM Switch No. with Key ID 4 Switch linked with key ID4 NONE, D MEM SW1, D MEM SW2, or D MEM SW3 NONE: No switches linked with key ID4
      D MEM SW1: M1 linked with key ID4
      D MEM SW2: M2 linked with key ID4
      D MEM SW3: M3 linked with key ID4*      		 -
      MEM Switch No. with Key ID 5 Switch linked with key ID5 NONE, D MEM SW1, D MEM SW2, or D MEM SW3 NONE: No switches linked with key ID5
      D MEM SW1: M1 linked with key ID5
      D MEM SW2: M2 linked with key ID5
      D MEM SW3: M3 linked with key ID5*      		 -
      MEM Switch No. with Key ID 6 Switch linked with key ID6 NONE, D MEM SW1, D MEM SW2, or D MEM SW3 NONE: No switches linked with key ID6
      D MEM SW1: M1 linked with key ID6
      D MEM SW2: M2 linked with key ID6
      D MEM SW3: M3 linked with key ID6*      		 -
      MEM Switch No. with Key ID 7 Switch linked with key ID7 NONE, D MEM SW1, D MEM SW2, or D MEM SW3 NONE: No switches linked with key ID7
      D MEM SW1: M1 linked with key ID7
      D MEM SW2: M2 linked with key ID7
      D MEM SW3: M3 linked with key ID7*      		 -
      Automatic Mirror Fold Setting Function that changes the condition under which the outer mirrors automatically retract state ACC, Door Lock or Disable Customize setting displayed -
      Reverse Coupled Actuation Mirror Angle Setting Function that turns the reverse shift-linked mirror position memorization function state Default Setting or User Setting Customize setting displayed -
      1. *: Not applicable

      Body Electrical > Mirror L > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Total Distance Traveled Total distance traveled Min.: 0, Max.: 16777215 - -
      Total Distance Traveled - Unit Unit for total distance traveled -, km, mile - -
      Mirror Horizontal Sensor Voltage Mirror horizontal position MIN: 0 V, MAX: 5 V 0 to 5 V -
      Mirror Vertical Sensor Voltage Mirror vertical position MIN: 0 V, MAX: 5 V 0 to 5 V -
      CPU Power Source Voltage Displays the power source voltage MIN: 0 mV, MAX: 655350 mV - -
      Memory Switch Set Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
      ON: Seat memory switch SET switch on      		 -
      Memory Switch Memory No. 1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
      ON: Seat memory switch M1 switch on      		 -
      Memory Switch Memory No. 2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
      ON: Seat memory switch M2 switch on      		 -
      Memory Switch Memory No. 3 Seat memory switch M3 switch signal OFF or ON OFF: Seat memory switch M3 switch off
      ON: Seat memory switch M3 switch on      		 Not applicable
      Mirror Fold Detect Displays whether mirror retraction lock is detected OFF or ON OFF: Retraction lock not detected
      ON: Retraction lock detected      		 -
      Mirror Fold Electric Current Monitor Displays the mirror retraction current MIN: 0 mA, MAX: 319.99 mA - -
      Overheat Detect Displays whether mirror overheat is detected OFF or ON OFF: Overheat not detected
      ON: Overheat detected      		 -
      Mirror Fold Overcurrent Detect Displays whether mirror retraction overcurrent is detected OFF or ON OFF: Retraction overcurrent not detected
      ON: Retraction overcurrent detected      		 -
      Mirror Overcurrent Detect Displays whether mirror surface overcurrent is detected OFF or ON OFF: Mirror surface overcurrent not detected
      ON: Mirror surface overcurrent detected      		 -
      Mirror Heater Overcurrent Detect Displays whether heater overcurrent is detected OFF or ON OFF: Overcurrent not detected
      ON: Overcurrent detected      		 -
      Foot Illumination Overcurrent Detect Displays whether foot illumination overcurrent is detected OFF or ON OFF: Overcurrent not detected
      ON: Overcurrent detected      		 -
      Status of Mirror Fold Status of mirror fold Stop, Fold, Return, Cranking Stop: Stop state
      Fold: Fold state
      Return: Returned to normal position
      Cranking: Stopped state due to cranking      		 -
      Mirror Angle Adjustment Signal Mirror angle adjustment signal Stop, Down, Up, Left, Right Stop: No angle adjustment signal
      Down: Down direction signal
      Up: Up direction signal
      Left: Left direction signal
      Right: Right direction signal      		 -
      Mirror Heater Displays whether the mirror heater is ON/OFF OFF or ON OFF: Mirror heater OFF
      ON: Mirror heater ON      		 -
      Foot Illumination Displays whether the foot illumination is ON/OFF OFF or ON OFF: Foot illumination OFF
      ON: Foot illumination ON      		 -
      Status of Mirror Working Displays the mirror operation status Uncertain, Stop, Manual, Memory, Reverse, Return Uncertain: Mirror status unknown
      Stop: Stop state
      Manual: Manual operating state
      Memory: Memory operating state
      Reverse: Reverse operating state
      Return: Returned to normal position      		 -
      Driver1 Memory No. 1 Position Memory Mirror position memorized in memory switch M1 (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver1 Memory No. 2 Position Memory Mirror position memorized in memory switch M2 (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver1 Memory No. 3 Position Memory Mirror position memorized in memory switch M3 (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      Driver1 Memory Last Position Memory Mirror position memorized in last position (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver1 Memory Reverse Last Position Memory Mirror position memorized in reverse last position (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver1 Memory No. 1 Horizontal Position Mirror horizontal position memorized in memory switch M1 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory No. 1 Vertical Position Mirror vertical position memorized in memory switch M1 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory No. 2 Horizontal Position Mirror horizontal position memorized in memory switch M2 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory No. 2 Vertical Position Mirror vertical position memorized in memory switch M2 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory No. 3 Horizontal Position Mirror horizontal position memorized in memory switch M3 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver1 Memory No. 3 Vertical Position Mirror vertical position memorized in memory switch M3 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver1 Memory Last Horizontal Position Mirror horizontal position memorized in last position (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory Last Vertical Position Mirror vertical position memorized in last position (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory Reverse Last Horizontal Position Mirror horizontal position memorized in reverse last position (driver 1) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver1 Memory Reverse Last Vertical Position Mirror vertical position memorized in reverse last position (driver 1) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver1 Endpoint This Side Stop Position Memory Mirror position memorized in reverse last position (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory No. 1 Position Memory Mirror position memorized in memory switch M1 (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory No. 2 Position Memory Mirror position memorized in memory switch M2 (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory No. 3 Position Memory Mirror position memorized in memory switch M3 (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      Driver2 Memory Last Position Memory Mirror position memorized in last position (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory Reverse Last Position Memory Mirror position memorized in reverse last position (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory No. 1 Horizontal Position Mirror horizontal position memorized in memory switch M1 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory No. 1 Vertical Position Mirror vertical position memorized in memory switch M1 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory No. 2 Horizontal Position Mirror horizontal position memorized in memory switch M2 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory No. 2 Vertical Position Mirror vertical position memorized in memory switch M2 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory No. 3 Horizontal Position Mirror horizontal position memorized in memory switch M3 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver2 Memory No. 3 Vertical Position Mirror vertical position memorized in memory switch M3 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver2 Memory Last Horizontal Position Mirror horizontal position memorized in last position (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory Last Vertical Position Mirror vertical position memorized in last position (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory Reverse Last Horizontal Position Mirror horizontal position memorized in reverse last position (driver 2) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver2 Memory Reverse Last Vertical Position Mirror vertical position memorized in reverse last position (driver 2) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver2 Endpoint This Side Stop Position Memory Mirror position memorized in reverse last position (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory No. 1 Position Memory Mirror position memorized in memory switch M1 (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory No. 2 Position Memory Mirror position memorized in memory switch M2 (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory No. 3 Position Memory Mirror position memorized in memory switch M3 (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      Driver3 Memory Last Position Memory Mirror position memorized in last position (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory Reverse Last Position Memory Mirror position memorized in reverse last position (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory No. 1 Horizontal Position Mirror horizontal position memorized in memory switch M1 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory No. 1 Vertical Position Mirror vertical position memorized in memory switch M1 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory No. 2 Horizontal Position Mirror horizontal position memorized in memory switch M2 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory No. 2 Vertical Position Mirror vertical position memorized in memory switch M2 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory No. 3 Horizontal Position Mirror horizontal position memorized in memory switch M3 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver3 Memory No. 3 Vertical Position Mirror vertical position memorized in memory switch M3 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver3 Memory Last Horizontal Position Mirror horizontal position memorized in last position (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory Last Vertical Position Mirror vertical position memorized in last position (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory Reverse Last Horizontal Position Mirror horizontal position memorized in reverse last position (driver 3) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver3 Memory Reverse Last Vertical Position Mirror vertical position memorized in reverse last position (driver 3) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver3 Endpoint This Side Stop Position Memory Mirror position memorized in reverse last position (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Memory No. 1 Position Memory Mirror position memorized in memory switch M1 OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Memory No. 2 Position Memory Mirror position memorized in memory switch M2 OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Memory No. 3 Position Memory Mirror position memorized in memory switch M3 OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      Memory Reverse Last Position Memory Mirror position memorized in reverse last position OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Memory No. 1 Horizontal Position Mirror horizontal position memorized in memory switch M1 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory No. 1 Vertical Position Mirror vertical position memorized in memory switch M1 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory No. 2 Horizontal Position Mirror horizontal position memorized in memory switch M2 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory No. 2 Vertical Position Mirror vertical position memorized in memory switch M2 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory No. 3 Horizontal Position Mirror horizontal position memorized in memory switch M3 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Memory No. 3 Vertical Position Mirror vertical position memorized in memory switch M3 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Memory Reverse Last Horizontal Position Mirror horizontal position memorized in reverse last position MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V -
      Memory Reverse Last Vertical Position Mirror vertical position memorized in reverse last position MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V -
      Endpoint This Side Stop Position Memory Displays whether endpoint stop position is memorized OFF or ON OFF: Not memorized
      ON: Memorized      		 -

      Body Electrical > Mirror R > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Total Distance Traveled Total distance traveled Min.: 0, Max.: 16777215 - -
      Total Distance Traveled - Unit Unit for total distance traveled -, km, mile - -
      Mirror Horizontal Sensor Voltage Mirror horizontal position MIN: 0 V, MAX: 5 V 0 to 5 V -
      Mirror Vertical Sensor Voltage Mirror vertical position MIN: 0 V, MAX: 5 V 0 to 5 V -
      CPU Power Source Voltage Displays the power source voltage MIN: 0 mV, MAX: 655350 mV - -
      Memory Switch Set Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
      ON: Seat memory switch SET switch on      		 Not applicable
      Memory Switch Memory No. 1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
      ON: Seat memory switch M1 switch on      		 Not applicable
      Memory Switch Memory No. 2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
      ON: Seat memory switch M2 switch on      		 Not applicable
      Memory Switch Memory No. 3 Seat memory switch M3 switch signal OFF or ON OFF: Seat memory switch M3 switch off
      ON: Seat memory switch M3 switch on      		 Not applicable
      Mirror Fold Detect Displays whether mirror retraction lock is detected OFF or ON OFF: Retraction lock not detected
      ON: Retraction lock detected      		 -
      Mirror Fold Electric Current Monitor Displays the mirror retraction current MIN: 0 mA, MAX: 319.99 mA - -
      Overheat Detect Displays whether mirror overheat is detected OFF or ON OFF: Overheat not detected
      ON: Overheat detected      		 -
      Mirror Fold Overcurrent Detect Displays whether mirror retraction overcurrent is detected OFF or ON OFF: Retraction overcurrent not detected
      ON: Retraction overcurrent detected      		 -
      Mirror Overcurrent Detect Displays whether mirror surface overcurrent is detected OFF or ON OFF: Mirror surface overcurrent not detected
      ON: Mirror surface overcurrent detected      		 -
      Mirror Heater Overcurrent Detect Displays whether heater overcurrent is detected OFF or ON OFF: Overcurrent not detected
      ON: Overcurrent detected      		 -
      Foot Illumination Overcurrent Detect Displays whether foot illumination overcurrent is detected OFF or ON OFF: Overcurrent not detected
      ON: Overcurrent detected      		 -
      Status of Mirror Fold Status of mirror fold Stop, Fold, Return, Cranking Stop: Stop state
      Fold: Fold state
      Return: Returned to normal position
      Cranking: Stopped state due to cranking      		 -
      Mirror Angle Adjustment Signal Mirror angle adjustment signal Stop, Down, Up, Left, Right Stop: No angle adjustment signal
      Down: Down direction signal
      Up: Up direction signal
      Left: Left direction signal
      Right: Right direction signal      		 -
      Mirror Heater Displays whether the mirror heater is ON/OFF OFF or ON OFF: Mirror heater OFF
      ON: Mirror heater ON      		 -
      Foot Illumination Displays whether the foot illumination is ON/OFF OFF or ON OFF: Foot illumination OFF
      ON: Foot illumination ON      		 -
      Status of Mirror Working Displays the mirror operation status Uncertain, Stop, Manual, Memory, Reverse, Return Uncertain: Mirror status unknown
      Stop: Stop state
      Manual: Manual operating state
      Memory: Memory operating state
      Reverse: Reverse operating state
      Return: Returned to normal position      		 -
      Driver1 Memory No. 1 Position Memory Mirror position memorized in memory switch M1 (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver1 Memory No. 2 Position Memory Mirror position memorized in memory switch M2 (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver1 Memory No. 3 Position Memory Mirror position memorized in memory switch M3 (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      Driver1 Memory Last Position Memory Mirror position memorized in last position (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver1 Memory Reverse Last Position Memory Mirror position memorized in reverse last position (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver1 Memory No. 1 Horizontal Position Mirror horizontal position memorized in memory switch M1 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory No. 1 Vertical Position Mirror vertical position memorized in memory switch M1 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory No. 2 Horizontal Position Mirror horizontal position memorized in memory switch M2 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory No. 2 Vertical Position Mirror vertical position memorized in memory switch M2 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory No. 3 Horizontal Position Mirror horizontal position memorized in memory switch M3 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver1 Memory No. 3 Vertical Position Mirror vertical position memorized in memory switch M3 (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver1 Memory Last Horizontal Position Mirror horizontal position memorized in last position (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory Last Vertical Position Mirror vertical position memorized in last position (driver 1) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver1 Memory Reverse Last Horizontal Position Mirror horizontal position memorized in reverse last position (driver 1) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver1 Memory Reverse Last Vertical Position Mirror vertical position memorized in reverse last position (driver 1) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver1 Endpoint This Side Stop Position Memory Mirror vertical position memorized in reverse last position (driver 1) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory No. 1 Position Memory Mirror position memorized in memory switch M1 (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory No. 2 Position Memory Mirror position memorized in memory switch M2 (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory No. 3 Position Memory Mirror position memorized in memory switch M3 (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      Driver2 Memory Last Position Memory Mirror position memorized in last position (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory Reverse Last Position Memory Mirror position memorized in reverse last position (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver2 Memory No. 1 Horizontal Position Mirror horizontal position memorized in memory switch M1 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory No. 1 Vertical Position Mirror vertical position memorized in memory switch M1 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory No. 2 Horizontal Position Mirror horizontal position memorized in memory switch M2 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory No. 2 Vertical Position Mirror vertical position memorized in memory switch M2 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory No. 3 Horizontal Position Mirror horizontal position memorized in memory switch M3 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver2 Memory No. 3 Vertical Position Mirror vertical position memorized in memory switch M3 (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver2 Memory Last Horizontal Position Mirror horizontal position memorized in last position (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory Last Vertical Position Mirror vertical position memorized in last position (driver 2) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver2 Memory Reverse Last Horizontal Position Mirror horizontal position memorized in reverse last position (driver 2) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver2 Memory Reverse Last Vertical Position Mirror vertical position memorized in reverse last position (driver 2) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver2 Endpoint This Side Stop Position Memory Mirror vertical position memorized in reverse last position (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory No. 1 Position Memory Mirror position memorized in memory switch M1 (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory No. 2 Position Memory Mirror position memorized in memory switch M2 (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory No. 3 Position Memory Mirror position memorized in memory switch M3 (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      Driver3 Memory Last Position Memory Mirror position memorized in last position (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory Reverse Last Position Memory Mirror position memorized in reverse last position (driver 2) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Driver3 Memory No. 1 Horizontal Position Mirror horizontal position memorized in memory switch M1 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory No. 1 Vertical Position Mirror vertical position memorized in memory switch M1 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory No. 2 Horizontal Position Mirror horizontal position memorized in memory switch M2 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory No. 2 Vertical Position Mirror vertical position memorized in memory switch M2 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory No. 3 Horizontal Position Mirror horizontal position memorized in memory switch M3 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver3 Memory No. 3 Vertical Position Mirror vertical position memorized in memory switch M3 (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Driver3 Memory Last Horizontal Position Mirror horizontal position memorized in last position (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory Last Vertical Position Mirror vertical position memorized in last position (driver 3) MIN: 0 V, MAX: 4.98 V 0 to 4.98 V w/ My Setting
      Driver3 Memory Reverse Last Horizontal Position Mirror horizontal position memorized in reverse last position (driver 3) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver3 Memory Reverse Last Vertical Position Mirror vertical position memorized in reverse last position (driver 3) MIN: 0 V, MAX: 1279.98 V 0 to 1279.98 V w/ My Setting
      Driver3 Endpoint This Side Stop Position Memory Mirror vertical position memorized in reverse last position (driver 3) OFF or ON OFF: Not memorized
      ON: Memorized      		 w/ My Setting
      Memory No. 1 Position Memory Mirror position memorized in memory switch M1 OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Memory No. 2 Position Memory Mirror position memorized in memory switch M2 OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Memory No. 3 Position Memory Mirror position memorized in memory switch M3 OFF or ON OFF: Not memorized
      ON: Memorized      		 Not applicable
      Memory Reverse Last Position Memory Mirror position memorized in reverse last position OFF or ON OFF: Not memorized
      ON: Memorized      		 -
      Memory No. 1 Horizontal Position Mirror horizontal position memorized in memory switch M1 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory No. 1 Vertical Position Mirror vertical position memorized in memory switch M1 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory No. 2 Horizontal Position Mirror horizontal position memorized in memory switch M2 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory No. 2 Vertical Position Mirror vertical position memorized in memory switch M2 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory No. 3 Horizontal Position Mirror horizontal position memorized in memory switch M3 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Memory No. 3 Vertical Position Mirror vertical position memorized in memory switch M3 MIN: 0 V, MAX: 4.98 V 0 to 4.98 V Not applicable
      Memory Reverse Last Horizontal Position Mirror horizontal position memorized in reverse last position MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Memory Reverse Last Vertical Position Mirror vertical position memorized in reverse last position MIN: 0 V, MAX: 4.98 V 0 to 4.98 V -
      Endpoint This Side Stop Position Memory Displays whether endpoint stop position is memorized OFF or ON OFF: Not memorized
      ON: Memorized      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Perform the Active Test according to the display on the GTS.

      Body Electrical > Mirror L > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Mirror Fold/Return Mirror retract operation Fold/Return
      • Operate with ignition switch ON and the vehicle stopped.
      • This test activates the Fold or Return.
      • This operation can be confirmed by watching the mirror move in the desired direction.
      Mirror Motor Mirror actuator operation Up/Down/Left/Right
      • Operate with ignition switch ON and the vehicle stopped.
      • This test tilts the mirror up, down, right or left.
      • This operation can be confirmed by watching the mirror move in the desired direction.
      Mirror Heater Mirror heater operation ON
      • Operate with ignition switch ON and the vehicle stopped.
      • This test turns the mirror heater on or off.
      • Mirror heater operation can be confirmed by touch.
      Foot Illumination Foot illumination operation ON Operate with ignition switch ON and the vehicle stopped.

      Body Electrical > Mirror R > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Mirror Fold/Return Mirror retract operation Fold/Return
      • Operate with ignition switch ON and the vehicle stopped.
      • This test activates the Fold or Return.
      • This operation can be confirmed by watching the mirror move in the desired direction.
      Mirror Motor Mirror actuator operation Up/Down/Left/Right
      • Operate with ignition switch ON and the vehicle stopped.
      • This test tilts the mirror up, down, right or left.
      • This operation can be confirmed by watching the mirror move in the desired direction.
      Mirror Heater Mirror heater operation ON
      • Operate with ignition switch ON and the vehicle stopped.
      • This test turns the mirror heater on or off.
      • Mirror heater operation can be confirmed by touch.
      Foot Illumination Foot illumination operation ON Operate with ignition switch ON and the vehicle stopped.
Diesel-Data.com