Reassembly [12/2019 - 09/2020]: Procedure

HINT: 

Perform this procedure only when replacement of the rear bumper reinforcement is necessary.

1. Install the rear bumper reinforcement with the 6 nuts.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 43 N.m (438 kgf/cm, 32 ft.lbf) 

HINT: 

Perform this procedure only when replacement of the rear bumper side seal LH is necessary.

1. Install the nut and clip.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   	Nut
   	Clip

2. Install the rear bumper side seal LH with the screw and clip.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   	Screw
   	Clip

HINT: 

Use the same procedure as for the LH side.

HINT: 

Perform this procedure only when replacement of the rear bumper side support LH is necessary.

1. Engage the 2 claws.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Engage the 3 clips as shown in the illustration to install the rear bumper side support LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

Use the same procedure as for the LH side.

1. Engage the 2 guides to install the rear bumper upper retainer LH to the rear combination light assembly LH.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

Use the same procedure as for the LH side.

1. Connect the 3 connectors.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Engage the 3 clamps.
3. Engage the guide and pin.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Guide
   *b	Pin

4. Install the rear combination light assembly LH with the 3 screws.

HINT: 

Use the same procedure as for the LH side.

HINT: 

When installing the rear bumper pad LH, heat the rear bumper cover using a heat light.

Heating Temperature

WARNING:

• Do not touch the heat light and heated parts, touching the heat light may result in burns.
• Touching heated parts for a long time may result in burns.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*a	Heated Part
*b	Heat Light

1. Clean the rear bumper cover surface.
   1. Using a heat light, heat the rear bumper cover surface.
   2. Remove any double-sided tape from the rear bumper cover.
   3. Wipe off any tape adhesive residue with cleaner.
2. Install a new rear bumper pad LH.
   1. Using a heat light, heat the rear bumper cover surface.
   2. Remove the release paper from the rear bumper pad LH.

      HINT: 

      After removing the release paper, keep the exposed adhesive free from foreign matter.

   3. Install the rear bumper pad LH as shown in the illustration.

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      *a

      Line

      HINT: 

      • Install the rear bumper pad LH along the line on the rear bumper cover.
      • Press the rear bumper pad LH firmly to install it.
      • Use the same procedure for the RH side and LH side.

1. Engage the 7 claws to install the rear bumper energy absorber.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Engage the 2 guides and 14 claws.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Install the rear bumper lower cover to the rear bumper cover with the 2 screws and 4 clips.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Screw

   Clip

1. Engage the 6 guides and 10 claws.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Install the 6 clips.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Install the rear bumper extension with each clip.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *A

   w/o Kick Sensor

   -

   -

1. Install the reflex reflector assembly LH with the 3 screws.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

Use the same procedure as for the LH side.

1. Engage the 15 clamps to install the No. 3 luggage room wire.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Refer to PROCEDURE - Step 2

Refer to PROCEDURE - Step 2

Refer to PROCEDURE - Step 3

Refer to PROCEDURE - Step 4

Refer to PROCEDURE - Step 5