DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Accessories & Equipment >> Exterior Lights >> Lighting System (W/O AFS) - Symptom Tests & Circuit Tests (2 Of 2) >> LIGHTING SYSTEM (w/o AFS) >> Taillight Relay Circuit [11/2023 - ] >> Procedure

Taillight Relay Circuit [11/2023 - ]: Procedure

  1. PERFORM ACTIVE TEST USING GTS 
    1. Read the Data List according to the display on the GTS.

      Body Electrical > Main Body > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Taillight / Clearance Light Taillights/parking lights OFF or ON -

      Body Electrical > Main Body > Active Test 

      Tester Display
      Taillight / Clearance Light

      OK

      taillights illuminate.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [11/2023 - ] 

    Result: 

    NG 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE - POWER DISTRIBUTION BOX ASSEMBLY) 
    1. Disconnect the 8J power distribution box assembly connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      8J-1 - Body ground Ignition switch off 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (TAILLIGHT CIRCUIT) 
    1. Disconnect the M59 rear combination light assembly LH connector.
    2. Disconnect the M8 rear combination light assembly RH connector.
    3. Disconnect the W8 rear light assembly LH connector.
    4. Disconnect the W7 rear light assembly RH connector.
    5. Disconnect the W5 license plate light assembly LH connector.
    6. Disconnect the W6 license plate light assembly RH connector.
    7. Disconnect the A70 front side marker light socket LH connector.
    8. Disconnect the A69 front side marker light socket RH connector.
    9. Disconnect the A66 headlight assembly LH connector.*1
    10. Disconnect the A65 headlight assembly RH connector.*1
    11. Disconnect the A68 front turn signal light socket LH connector.*2
    12. Disconnect the A67 front turn signal light socket RH connector.*2
    13. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M59-2 (TL) - 8G-30 Always Below 1 Ω
      M8-2 (TL) - 8G-30 Always Below 1 Ω
      W8-2 (B) - 8G-30 Always Below 1 Ω
      W7-2 (B) - 8G-30 Always Below 1 Ω
      W5-1 (B) - 8G-30 Always Below 1 Ω
      W6-1 (B) - 8G-30 Always Below 1 Ω
      A70-2 (B) - 8E-18 Always Below 1 Ω
      A69-2 (B) - 8E-18 Always Below 1 Ω
      A66-2 (B) - 8E-18*1 Always Below 1 Ω
      A65-2 (B) - 8E-18*1 Always Below 1 Ω
      A68-2 (B) - 8E-18*2 Always Below 1 Ω
      A67-2 (B) - 8E-18*2 Always Below 1 Ω
      M59-2 (TL), M8-2 (TL), W8-2 (B), W7-2 (B), W5-1 (B), W6-1 (B) or 8G-30 - Body ground Always 10 kΩ or higher
      A70-2 (B), A69-2 (B), A66-2 (B)*1, A65-2 (B)*1, A68-2 (B)*2, A67-2 (B)*2 or 8E-18 - Body ground Always 10 kΩ or higher
      1. *1: for LED Type Parking Light
      2. *2: for Bulb Type Parking Light

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK POWER DISTRIBUTION BOX ASSEMBLY 
    1. Connect the 8J power distribution box assembly connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      8E-18 - Body ground Always 11 to 14 V
      8G-30 - Body ground Always 11 to 14 V

      Result

      Result
      OK
      NG

    Result: 

    NG 

    REPLACE POWER DISTRIBUTION BOX ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    OK 

    See step  5

  5. CHECK REAR COMBINATION LIGHT ASSEMBLY LH 
    1. Connect the M59 rear combination light assembly LH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Ignition switch off 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR COMBINATION LIGHT ASSEMBLY LH. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    OK 

    See step  6

  6. CHECK REAR COMBINATION LIGHT ASSEMBLY RH 
    1. Connect the M8 rear combination light assembly RH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Ignition switch off 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR COMBINATION LIGHT ASSEMBLY RH. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    OK 

    See step  7

  7. CHECK REAR LIGHT ASSEMBLY LH 
    1. Connect the W8 rear light assembly LH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Ignition switch off 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR LIGHT ASSEMBLY LH. Refer to  REMOVAL [12/2019 - ] 

    Result: 

    OK 

    See step  8

  8. CHECK REAR LIGHT ASSEMBLY RH 
    1. Connect the W7 rear light assembly RH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Ignition switch off 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE REAR LIGHT ASSEMBLY RH. Refer to  REMOVAL [12/2019 - ] 

    Result: 

    OK 

    See step  9

  9. CHECK FRONT SIDE MARKER LIGHT SOCKET LH 
    1. Connect the A70 front side marker light socket LH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  21

    Result: 

    OK 

    See step  10

  10. CHECK FRONT SIDE MARKER LIGHT SOCKET RH 
    1. Connect the A69 front side marker light socket RH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Result Proceed to
      OK (for LED Type Parking Light) A
      OK (for Bulb Type Parking Light) B
      NG C

    Result: 

    B 

    See step  13

    Result: 

    C 

    See step  20

    Result: 

    A 

    See step  11

  11. CHECK HEADLIGHT ASSEMBLY LH 
    1. Connect the A66 headlight assembly LH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE HEADLIGHT ASSEMBLY LH. Refer to  DISASSEMBLY [12/2019 - ] 

    Result: 

    OK 

    See step  12

  12. CHECK HEADLIGHT ASSEMBLY RH 
    1. Connect the A65 headlight assembly RH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  15

    Result: 

    NG 

    REPLACE HEADLIGHT ASSEMBLY RH. Refer to  REMOVAL [11/2023 - ] 

  13. CHECK FRONT TURN SIGNAL LIGHT SOCKET LH 
    1. Connect the A68 front turn signal light socket LH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  19

    Result: 

    OK 

    See step  14

  14. CHECK FRONT TURN SIGNAL LIGHT SOCKET RH 
    1. Connect the A67 front turn signal light socket RH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  18

    Result: 

    OK 

    See step  15

  15. CHECK LICENSE PLATE LIGHT ASSEMBLY LH 
    1. Connect the W5 license plate light assembly LH connector.
    2. Turn the light control switch to the tail position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Ignition switch off 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  17

    Result: 

    OK 

    See step  16

  16. CHECK LICENSE PLATE LIGHT BULB RH 
    1. Disconnect the license plate light bulb RH connector.
    2. Turn the light control switch to the TAIL position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE LICENSE PLATE LIGHT BULB RH. Refer to  REPLACEMENT [12/2019 - ] 

    Result: 

    NG 

    REPLACE LICENSE PLATE LIGHT ASSEMBLY RH. Refer to  REMOVAL [12/2019 - ] 

  17. CHECK LICENSE PLATE LIGHT BULB LH 
    1. Disconnect the license plate light bulb LH connector.
    2. Turn the light control switch to the TAIL position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE LICENSE PLATE LIGHT BULB LH. Refer to  REPLACEMENT [12/2019 - ] 

    Result: 

    NG 

    REPLACE LICENSE PLATE LIGHT ASSEMBLY LH. Refer to  REMOVAL [12/2019 - ] 

  18. CHECK FRONT TURN SIGNAL LIGHT BULB RH 
    1. Disconnect the front turn signal light bulb RH connector.
    2. Turn the light control switch to the TAIL position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE FRONT TURN SIGNAL LIGHT BULB RH. Refer to  REPLACEMENT [12/2019 - ] 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT SOCKET RH. Refer to  REMOVAL [11/2023 - ] 

  19. CHECK FRONT TURN SIGNAL LIGHT BULB LH 
    1. Disconnect the front turn signal light bulb LH connector.
    2. Turn the light control switch to the TAIL position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE FRONT TURN SIGNAL LIGHT BULB LH. Refer to  REPLACEMENT [12/2019 - ] 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT SOCKET LH. Refer to  DISASSEMBLY [12/2019 - ] 

  20. CHECK FRONT SIDE MAKER LIGHT BULB RH 
    1. Disconnect the front side maker light bulb RH connector.
    2. Turn the light control switch to the TAIL position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE FRONT SIDE MAKER LIGHT BULB RH. Refer to  REPLACEMENT [12/2019 - ] 

    Result: 

    NG 

    REPLACE FRONT SIDE MARKER LIGHT SOCKET RH. Refer to  DISASSEMBLY [12/2019 - ] 

  21. CHECK FRONT SIDE MAKER LIGHT BULB LH 
    1. Disconnect the front side maker light bulb LH connector.
    2. Turn the light control switch to the TAIL position.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      W6-1 (B) - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE FRONT SIDE MAKER LIGHT BULB LH. Refer to  REPLACEMENT [12/2019 - ] 

    Result: 

    NG 

    REPLACE FRONT SIDE MARKER LIGHT SOCKET LH. Refer to  DISASSEMBLY [12/2019 - ] 

Diesel-Data.com