DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Power Back Door System - Diagnostic Codes & Symptom Tests >> Power Back Door System >> DTC B2204-9E: Kick Sensor Stuck ON [11/2023 - ] >> Procedure

DTC B2204-9E: Kick Sensor Stuck ON [11/2023 - ]: Procedure

  1. CLEAR DTC 
    1. Clear the DTCs.

      Body Electrical > Back Door > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  2

  2. REPRODUCE DTC 
    1. Turn the ignition switch to ON and wait for at least 60 seconds.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  3

  3. CHECK FOR DTC 
    1. Check for DTCs.

      Body Electrical > Back Door > Trouble Codes 

      Result

      Result Proceed to
      B2204-9E is not output A
      B2204-9E is output B

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [12/2019 - ] 

    Result: 

    B 

    See step  4

  4. CLEAR DTC 
    1. Clear the DTCs.

      Body Electrical > Back Door > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  5

  5. REPRODUCE DTC 

    Pre-procedure1

    1. Disconnect the V7*1 or V8*2 kick door control sensor connector.
      1. *1: w/o Option Connector (Trailer Towing)
      2. *2: w/ Option Connector (Trailer Towing)

      Procedure1

    2. Turn the ignition switch to ON and wait for at least 60 seconds.

      Result

      Proceed to
      NEXT

      Post-procedure1

    3. None

    Result: 

    NEXT 

    See step  6

  6. CHECK FOR DTC 
    1. Check for DTCs.

      Body Electrical > Back Door > Trouble Codes 

      Result

      Result Proceed to
      B2204-9E is not output A
      B2204-9E is output B

    Result: 

    A 

    REPLACE KICK DOOR CONTROL SENSOR. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    B 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - KICK DOOR CONTROL SENSOR) 

    Pre-procedure1

    1. Disconnect the W30 multiplex network door ECU connector.
    2. Disconnect the V7*1 or V8*2 kick door control sensor connector.
      1. *1: w/o Option Connector (Trailer Towing)
      2. *2: w/ Option Connector (Trailer Towing)

      Procedure1

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      W/O OPTION CONNECTOR (TRAILER TOWING)

      Tester Connection Condition Specified Condition
      W30-12 (KSIN) or V7-3 (KSOT) - Body ground Always 10 kΩ or higher
      W/ OPTION CONNECTOR (TRAILER TOWING)

      Tester Connection Condition Specified Condition
      W30-12 (KSIN) or V8-3 (KSOT) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

      Post-procedure1

    4. None

    Result: 

    OK 

    REPLACE MULTIPLEX NETWORK DOOR ECU. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

Diesel-Data.com