DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Power Back Door System - Diagnostics - Introduction >> Power Back Door System >> Data List / Active Test [12/2019 - 11/2023] >> Data List / Active Test [12/2019 - 11/2023]

Data List / Active Test [12/2019 - 11/2023]

  1. DATA LIST 
    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT: 

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Body Electrical / Back Door, Main Body or Smart Key / Data List.
    5. Read the Data List according to the display on the GTS

      Body Electrical > Back Door > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Door Lock Status Back door condition signal Unlock or Lock Unlock: Back door unlocked
      Lock: Back door locked      		 -
      Half Latch SW Half-latch switch signal OFF or ON OFF: Back door lock motor in full latch or half latch position
      ON: Back door lock motor in open latch position      		 -
      Closer Position SW Position switch signal OFF or ON OFF: Back door lock center gear out of center position (Position switch off)
      ON: Back door lock center gear in center position (Position switch on)      		 -
      Pawl Position Switch Pawl switch signal OFF or ON OFF: Back door lock motor except open latched
      ON: Back door lock motor open latched      		 -
      Courtesy SW Back door courtesy switch signal OFF or ON OFF: Back door closed
      ON: Back door open      		 -
      PBD Touch Sensor (Right) Power back door sensor assembly RH signal OFF, ON or Open OFF: Power back door sensor assembly RH not pressed
      ON: Power back door sensor assembly RH pressed
      Open: Power back door sensor assembly RH circuit open      		 -
      PBD Touch Sensor (Left) Power back door sensor assembly LH signal OFF, ON or Open OFF: Power back door sensor assembly LH not pressed
      ON: Power back door sensor assembly LH pressed
      Open: Power back door sensor assembly LH circuit open      		 -
      PBD Main SW Power back door ON/OFF signal OFF or ON Customize setting displayed -
      PBD Close SW No. 1 power back door control switch signal OFF or ON OFF: No. 1 power back door control switch not pressed
      ON: No. 1 power back door control switch pressed      		 -
      IG SW Ignition switch signal OFF or ON OFF: Ignition switch off
      ON: Ignition switch ON      		 "OFF" is also displayed for this item when the ignition switch is ACC.
      Door Lock Signal Back door condition signal Unlock or Lock Unlock: Back door unlocked
      Lock: Back door locked      		 -
      PBD Position (3/4-Open) Load signal detected during back door closing operation (3/4 - Open) Caution or OK Caution: Load detected between back door 3/4 and fully open position during back door closing operation
      OK: No load detected between back door 3/4 and fully open position during back door closing operation      		 -
      PBD Position (2/4-3/4) Load signal detected during back door closing operation (2/4 - 3/4) Caution or OK Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation
      OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation      		 -
      PBD Position (1/4-2/4) Load signal detected during back door closing operation (1/4 - 2/4) Caution or OK Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation
      OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation      		 -
      PBD Position (Close-1/4) Load signal detected during back door closing operation (Close - 1/4) Caution or OK Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation
      OK: No load detected between back door fully closed and 1/4 open position during back door closing operation      		 -
      Closed Position Initialization Back door fully closed position memorized signal Not Initialized or Initialized Not Initialized: Back door fully closed position not memorized
      Initialized: Back door fully closed position memorized      		 -
      PBD SW Operation Power back door control switch operation 0.0 s or 0.8 s Customize setting displayed -
      PBD Buzz In Use Power back door warning buzzer operation condition signal OFF or ON Customize setting displayed -
      PBD Assist Open Operation Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated. OFF or ON Customize setting displayed -
      PBD Assist Close Operation Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. OFF or ON Customize setting displayed -
      Door Unlock with 1 Motion. Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch Back Door or ALL DOORS Customize setting displayed -
      Wireless Power Back Door Open Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). Lock:OFF/Unlock:OFF, Lock:OFF/Unlock:ON, Lock:OFF/Unlock:Twice, Lock:OFF/Unlock:0.8s, Lock:Twice/Unlock:Twice or Lock:0.8s/Unlock: 0.8s Customize setting displayed -
      Power Back Door Opening Adjust Function that changes the position that the power back door stops during an open operation. 1:Min, 2:Small, 3:Middle, 4:Large, 5:Max or User Setting Position Customize setting displayed -
      Emblem Sensor Rear emblem sensor assembly connection status*1 Without or With Without: Rear emblem sensor assembly not connected
      With: Rear emblem sensor assembly connected      		 Not applicable
      Emblem Sensor Detection Rear emblem sensor assembly detection status*1 OFF or ON OFF: Rear emblem sensor assembly not detecting a hand
      ON: Rear emblem sensor assembly detecting a hand      		 Not applicable
      PBD/Emblem Sensor Function Function that enables/disables the power back door and rear emblem sensor assembly.*1 PBD OFF/Emblem OFF, PBD ON/Emblem OFF or PBD ON/Emblem ON Customize setting displayed Not applicable
      PBD Buzzer Volume Adjust Function that changes the volume setting of the power back door warning buzzer. Small, Middle or Large Customize setting displayed -
      Emblem Sensor Detection Sensitivity Function that changes the sensitivity of the rear emblem sensor assembly.*1 Low, Middle or High Customize setting displayed Not applicable
      Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Frequent Contact/Calibration Failure) Number of times emblem sensor changed to sensitivity reduction mode (frequent contact/calibration failure)*1 None, Low, Middle or High None: Never
      Low: 1 to 10 times
      Middle: 11 to 50 times
      High: 51 times or more      		 Not applicable
      Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Power Saving) Number of times emblem sensor changed to sensitivity reduction mode (power saving)*1 None, Low, Middle or High None: Never
      Low: 1 to 10 times
      Middle: 11 to 50 times
      High: 51 times or more      		 Not applicable
      Emblem Sensor Sensitivity Drop Frequency (Disturbance Factor) Number of times emblem sensor sensitivity decreased (wave interference)*1 None, Low, Middle or High None: Never
      Low: 1 to 10 times
      Middle: 11 to 50 times
      High: 51 times or more      		 Not applicable
      Emblem Sensor Sensitivity Drop Frequency (Foreign Matter Adhering) Number of times emblem sensor sensitivity decreased (adherence of foreign matter)*1 None, Low, Middle or High None: Never
      Low: 1 to 10 times
      Middle: 11 to 50 times
      High: 51 times or more      		 Not applicable
      Kick Sensor Connection Status of the kick door control sensor connection*2 Without or With Without: kick door control sensor not equipped
      With: kick door control sensor equipped      		 -
      Kick Sensor Detection Status of the kick door control sensor detection*2 OFF or ON OFF: Kick door control sensor not detecting a foot
      ON: Kick door control sensor detecting a foot      		 -
      Kick Sensor Error Status of the kick door control sensor error*2 Normal or Error Normal: Kick door control sensor is normal
      Error: Kick door control sensor is abnormal      		 -
      Kick Sensor Function Status of the hands free power back door function*2 OFF or ON Customize setting displayed -
      #Codes Number of DTCs Min.: 0, Max.: 255 Number of output DTCs -
      1. *1: Although the item is displayed on the GTS, it is not applicable to this vehicle.
      2. *2: w/ Hands Free Power Back Door

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Back Door Courtesy SW Back door courtesy light switch signal OFF or ON OFF: Back door closed
      ON: Back door open      		 -
      Back Door Open Back door lock Permit or Prohibit Permit: Back door unlocked
      Prohibit: Back door locked      		 -
      Back Door Open SW Power back door control switch signal OFF or ON OFF: Power back door control switch off
      ON: Power back door control switch on      		 -
      Kick Sensor Operation with ACC ON Status of the hands free power back door function with ignition switch ACC.* Available or Not Available Customize setting displayed -
      1. *: w/ Hands Free Power Back Door

      Body Electrical > Smart Key > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Tr/B-Door Unlock SW Back door opener switch assembly (open switch) signal OFF or ON OFF: Back door opener switch assembly (open switch) off
      ON: Back door opener switch assembly (open switch) on      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Body Electrical / Back Door / Active Test.
    5. Perform the Active Test according to the display on the GTS

      Body Electrical > Back Door > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Latch Release Latch release operation OFF or ON -
      PBD Open/Close Power back door motor operation Forward, Reverse or OFF -
      PBD Buzzer Power back door warning buzzer sound OFF or ON -
Diesel-Data.com