DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Restraints >> Passive Restraints >> Seat Belt - Service Information >> Front Seat Outer Belt Assembly With Pre-TENSIONER >> Installation [12/2019 - 10/2022] >> Procedure

Installation [12/2019 - 10/2022]: Procedure

  1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY 

    HINT: 

    Perform this procedure only when replacement of the front shoulder belt anchor adjuster assembly is necessary.

    1. Engage the guide and temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.
      GTY885137Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Fully tighten the bolt (A) first, then the bolt (B) to install the front shoulder belt anchor adjuster assembly.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  2. INSPECT FRONT SEAT OUTER BELT ASSEMBLY 

    See step  1

  3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY 
    1. Engage the 2 guides.
    2. Fully tighten the bolt.

      Bolt (A) 

      Torque: 12.5 N*m (127 kgf*cm, 9 ft.*lbf) 

    3. for LH Side:
      1. Connect the pretensioner connector and lock the locking button as shown in the illustration.
        GTY900560Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Locking Button
        *b Lock
        NOTE:

        Securely lock the locking button.

    4. for RH Side:
      1. Connect the selectable force limiter connector and lock the locking button as shown in the illustration.
        NOTE:

        Securely lock the locking button.

        GTY895886Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Locking Button
        *b Lock
        *c Pretensioner Connector
        *d Selectable Force Limiter Connector
      2. Connect the pretensioner connector and lock the locking button as shown in the illustration.
        NOTE:

        Securely lock the locking button.

    5. Check that the ELR locks.
      NOTE:

      The check should be performed with the front seat outer belt assembly installed.

      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
    6. Connect the shoulder anchor of the front seat outer belt assembly with the nut.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  4. INSTALL CENTER PILLAR GARNISH ASSEMBLY 

    Refer to PROCEDURE - Step 42

  5. INSTALL LOWER CENTER PILLAR GARNISH 

    Refer to PROCEDURE - Step 42

  6. CONNECT FRONT SEAT OUTER BELT ASSEMBLY 
    1. Connect the floor anchor of the front seat outer belt assembly with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  7. INSTALL LAP BELT OUTER ANCHOR COVER 
    1. Engage the 3 claws to install the lap belt outer anchor cover.
  8. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP 

    Refer to PROCEDURE - Step 1

  9. INSTALL REAR DOOR SCUFF PLATE 

    Refer to PROCEDURE - Step 47

  10. INSTALL REAR OUTER SEAT TRACK BRACKET COVER 

    Refer to PROCEDURE - Step 48

  11. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP 

    Refer to PROCEDURE - Step 1

  12. INSTALL FRONT DOOR SCUFF PLATE 

    Refer to PROCEDURE - Step 52

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [12/2019 - 09/2020] , or refer to INITIALIZATION [09/2020 - 10/2021] , or refer to INITIALIZATION [10/2021 - 10/2022]

  14. INSTALL BATTERY SERVICE HOLE COVER (for HV Model) 

    Refer to PROCEDURE - Step 3

  15. INSPECT SRS WARNING LIGHT 

    Refer to SYSTEM DIAGRAM [12/2019 - 10/2021] , or refer to SYSTEM DIAGRAM [10/2021 - 11/2023]

Diesel-Data.com