DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Drivelines & Axles >> Axle Shafts >> Drive Shaft / Propeller Shaft - Service Information >> FRONT DRIVE SHAFT ASSEMBLY (for 2GR-FKS) >> Removal [12/2019 - 10/2022] >> Procedure

Removal [12/2019 - 10/2022]: Procedure

  1. REMOVE FRONT WHEELS 

    Refer to REMOVAL [12/2019 - 10/2022]

  2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 8 [12/2019 - 09/2020] , or refer to PROCEDURE - Step 8 [09/2020 - 10/2022]

  3. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 9 [12/2019 - 09/2020] , or refer to PROCEDURE - Step 9 [09/2020 - 10/2022]

  4. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10 [12/2019 - 09/2020] , or refer to PROCEDURE - Step 10 [09/2020 - 10/2022]

  5. REMOVE REAR ENGINE UNDER COVER LH 

    Refer to PROCEDURE - Step 11 [12/2019 - 09/2020] , or refer to PROCEDURE - Step 11 [09/2020 - 10/2022]

  6. REMOVE REAR ENGINE UNDER COVER RH 

    Refer to PROCEDURE - Step 12 [12/2019 - 09/2020] , or refer to PROCEDURE - Step 12 [09/2020 - 10/2022]

  7. REMOVE FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 15 [12/2019 - 09/2020] , or refer to PROCEDURE - Step 15 [09/2020 - 10/2022]

  8. REMOVE FRONT FENDER APRON SEAL RH 

    Refer to PROCEDURE - Step 16 [12/2019 - 09/2020] , or refer to PROCEDURE - Step 16 [09/2020 - 10/2022]

  9. DRAIN AUTOMATIC TRANSAXLE FLUID 

    for UA80E: Refer to PROCEDURE - Step 3

    for UA80F: Refer to PROCEDURE - Step 3

  10. DRAIN TRANSFER OIL (for AWD) 

    Refer to PROCEDURE - Step 1

  11. REMOVE FRONT AXLE SHAFT NUT 
    1. Using SST and a hammer, release the staked part of the front axle shaft nut.
      GTY850226Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09930-00010 
      NOTE:

      Fully loosen the staked part of the front axle shaft nut, otherwise the threads of the drive shaft may be damaged.

    2. While applying the brakes, using a 30 mm deep socket wrench, remove the front axle shaft nut.
  12. SEPARATE FRONT SPEED SENSOR 

    Refer to PROCEDURE - Step 4

  13. SEPARATE TIE ROD ASSEMBLY 

    Refer to PROCEDURE - Step 6

  14. SEPARATE FRONT STABILIZER LINK ASSEMBLY 

    Refer to PROCEDURE - Step 11

  15. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 8

  16. SEPARATE FRONT DRIVE SHAFT ASSEMBLY 

    Refer to PROCEDURE - Step 9

  17. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH 
    1. Using SST, remove the front drive shaft assembly LH.
      GTY930956Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • SST: 09520-01011 
      • SST: 09520-20010 
        1. 09521-02010
        2. 09521-02040
        3. 09521-02060
      NOTE:
      • Do not damage the front drive shaft oil seal LH.
      • Do not damage the front axle inboard joint boot.
      • Do not drop the front drive shaft assembly LH.
  18. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD) 
    1. Remove the 2 bolts and pull out the drive shaft together with the drive shaft bearing case sub-assembly.
      GTY846883Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the front drive shaft assembly RH from the drive shaft bearing bracket.
      NOTE:
      • Do not damage the front drive shaft oil seal RH.
      • Do not damage the front axle inboard joint boot.
      • Do not drop the front drive shaft assembly RH.

      HINT: 

      If it is difficult to disengage the fitting, tap the end of the front drive inboard joint assembly with a brass bar and a hammer.

  19. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for AWD) 
    1. Separate the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.
      GTY846884Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the No. 1 drive shaft bearing bracket setting bolt and front drive shaft assembly RH from the transfer assembly.
      NOTE:
      • Do not damage the transfer case oil seal RH.
      • Do not damage the front axle inboard joint boot.
      • Do not drop the front drive shaft assembly RH.

      HINT: 

      If it is difficult to disengage the fitting, tap the end of the front drive inboard joint assembly with a brass bar and a hammer.

    3. Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.
  20. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING 
    1. Using a screwdriver, remove the front drive shaft hole snap ring.
      GTY363502Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Diesel-Data.com