DSD Information System
Home >> Toyota >> 2021 >> Highlander LE, 4WD >> Repair and Diagnosis >> Drivelines & Axles >> Driveshaft & Universal Joints >> Drive Shaft / Propeller Shaft - Service Information >> REAR DRIVE SHAFT ASSEMBLY (for A25A-FXS) >> Installation [12/2019 - ] >> Procedure

Installation [12/2019 - ]: Procedure

  1. INSTALL REAR DRIVE SHAFT SNAP RING 
    1. Install a new rear drive shaft snap ring.
      NOTE:

      Face the end gap of the rear drive shaft snap ring downward.

  2. INSTALL REAR DRIVE SHAFT ASSEMBLY 
    1. Coat the rear drive shaft snap ring of the rear drive shaft inboard joint assembly with MP grease.
    2. Coat the splines of the rear drive shaft inboard joint assembly with Toyota genuine ATF WS.
    3. Align the inboard joint splines, and using a brass bar and a hammer, install the rear drive shaft assembly.
      GTY677680Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Face the end gap of the rear drive shaft snap ring downward.
      • Do not damage the rear drive shaft oil seal.
      • Do not damage the rear drive shaft inboard joint boot.
      • Make sure to center the rear drive shaft assembly during installation to prevent damage to the rear drive shaft snap ring.

      HINT: 

      Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.

    4. Align the matchmarks and install the rear drive shaft assembly to the rear axle hub and bearing assembly.
      NOTE:
      • Do not damage the rear disc brake dust cover sub-assembly.
      • Do not damage the rear drive shaft outboard joint boot.
      • Check that there is no foreign matter on the contact surfaces.
      • Do not push the rear axle carrier sub-assembly towards the outside of the vehicle any further than necessary.
      GTY642058Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
  3. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY 

    Refer to PROCEDURE - Step 20

  4. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY 

    Refer to PROCEDURE - Step 1 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 1 [10/2022 - ]

  5. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY 

    Refer to PROCEDURE - Step 2 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 2 [10/2022 - ]

  6. INSTALL REAR LOWER COIL SPRING INSULATOR 

    Refer to PROCEDURE - Step 3 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 3 [10/2022 - ]

  7. INSTALL REAR COIL SPRING 

    Refer to PROCEDURE - Step 4 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 4 [10/2022 - ]

  8. CONNECT REAR STABILIZER LINK ASSEMBLY 

    Refer to PROCEDURE - Step 7 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 7 [10/2022 - ]

  9. INSTALL REAR SKID CONTROL SENSOR 

    Refer to PROCEDURE - Step 14

  10. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY 

    Refer to PROCEDURE - Step 36

  11. INSTALL REAR AXLE SHAFT NUT 

    Refer to PROCEDURE - Step 11

  12. CONNECT REAR FLEXIBLE HOSE 

    Refer to PROCEDURE - Step 10

  13. STABILIZE SUSPENSION 

    Refer to PROCEDURE - Step 3

  14. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY 

    Refer to PROCEDURE - Step 7 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 7 [10/2022 - ]

  15. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY 

    Refer to PROCEDURE - Step 8 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 8 [10/2022 - ]

  16. INSTALL REAR UPPER CONTROL ARM ASSEMBLY 

    Refer to PROCEDURE - Step 8

  17. INSTALL REAR SUSPENSION ARM COVER 

    Refer to PROCEDURE - Step 9 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 9 [10/2022 - ]

  18. INSTALL TAIL EXHAUST PIPE ASSEMBLY (for RH Side) 

    Refer to PROCEDURE - Step 3 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 3 [10/2022 - ]

  19. INSTALL REAR WHEEL 

    Refer to INSTALLATION [12/2019 - 10/2022] , or refer to INSTALLATION [10/2022 - ]

  20. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY 

    Refer to PROCEDURE - Step 12 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 8 [10/2022 - ]

  21. ADD HYBRID TRANSAXLE FLUID 

    Refer to PROCEDURE - Step 2

  22. INSPECT HYBRID TRANSAXLE FLUID 

    Refer to PROCEDURE - Step 1

  23. INSPECT FOR HYBRID TRANSAXLE FLUID LEAK 
  24. INSPECT FOR EXHAUST GAS LEAK (for RH Side) 

    Refer to PROCEDURE - Step 6 [12/2019 - 10/2022] , or refer to PROCEDURE - Step 6 [10/2022 - ]

  25. INSPECT AND ADJUST REAR WHEEL ALIGNMENT 

    Refer to ADJUSTMENT [12/2019 - 09/2020] , or refer to ADJUSTMENT [09/2020 - 10/2022] , or refer to ADJUSTMENT [10/2022 - 11/2023] , or refer to ADJUSTMENT [11/2023 - 11/2024] , or refer to ADJUSTMENT [11/2024 - ]

  26. CHECK FOR SPEED SENSOR SIGNAL 

    Refer to TEST MODE PROCEDURE [12/2019 - 11/2023] , or refer to TEST MODE PROCEDURE [11/2023 - ]

  27. PERFORM INITIALIZATION 
Diesel-Data.com